CLIFFORD MATRIX 70.5X Скачать руководство пользователя | Manualshive

Страница: 62 / 70

background image

© 2006 Directed Electronics—all rights reserved

2

long term event history

The system stores the last two full triggers in memory. These are not erasable. Each time the unit sees a
full trigger, the older of the two triggers in memory will be replaced by the new trigger. To access long term
event history:

1.

With the ignition off, press and

HOLD

the Valet/Program switch.

2.

Turn on the ignition.

3.

Release the Valet/Program switch.

4.

Press and release the Valet/Program switch within 5 seconds. The
LED will flash in groups indicating the last two zones that triggered
the unit for one minute or until the ignition is turned off. Refer to
table of zones.

NOTE:

The Warn Away triggers are not stored to memory and will not be reported.

«
...
60
61
62
63
64
...
»

Содержание 70.5X







































































Отзывы:

Нет отзывов

Похожие инструкции для 70.5X

Бренд: Clifford Страницы: 53

Бренд: Audiovox Страницы: 12

Бренд: Hama Страницы: 4

Бренд: Velleman Страницы: 20

Бренд: Directed Electronics Страницы: 37

Бренд: Ness Страницы: 4

Бренд: Konyks Страницы: 8

Бренд: iHome Страницы: 16

Бренд: iHome Страницы: 20

Бренд: System Sensor Страницы: 4

Бренд: Jazwares Страницы: 12

Бренд: Jazwares Страницы: 12

Бренд: Code Alarm Страницы: 33

Бренд: Johnson Страницы: 16

Radio-Controlled Travel Alarm Clock WT-2160

Бренд: La Crosse Technology Страницы: 18

Бренд: HumanTechnik Страницы: 50

Бренд: Silencer Страницы: 9

Бренд: B52 Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды