CLIFFORD MATRIX 70.5X Скачать руководство пользователя | Manualshive

Страница: 5 / 70

background image

what is included

■

The control module

■

The plug-in status LED

■

A Responder receiver/antenna

■

The plug-in Valet/Program switch

■

One 2-way Color Remote Control

■

A hood pinswitch

■

A Stinger Doubleguard shock sensor

■

A toggle (override) switch

■

A 514N Neosiren

■

One Remote Control charger

warning! safety first

The following safety warnings must be observed at all times:

■

Due to the complexity of this system, installation of this product must only be performed by an autho-

rized Directed Electronics dealer.

■

When properly installed, this system can start the vehicle via a command signal from the remote control

Therefore,  never  operate  the  system  in  an  area  that  does  not  have  adequate  ventilation.  The  following
precautions are the sole responsibility of the user; however, authorized Directed Electronics dealers should
make the following recommendations to all users of this system:
1.  Never  operate  the  system  in  an  enclosed  or  partially  enclosed  area  without  ventilation  (such  as  a
garage).
2. When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote
start system must be disabled using the installed toggle switch.
3.  It  is  the  user's  sole  responsibility  to  properly  handle  and  keep  out  of  reach  from  children  all  remote
controls to assure that the system does not unintentionally remote start the vehicle.
4.

THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT

TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY
ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED.

■

Use of this product in a manner contrary to its intended mode of operation may result in property damage,

personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1)
Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the
keys in the ignition. The user will be responsible for having the neutral safety feature of the vehicle peri-
odically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should
be performed by an authorized Directed Electronics dealer in accordance with the Safety Check outlined in
this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and
consult with the user to fix the problem immediately.

«
...
3
4
5
6
7
...
»

Содержание 70.5X







































































Отзывы:

Нет отзывов

Похожие инструкции для 70.5X

Бренд: Olympia Страницы: 54

Бренд: Climax Technology Страницы: 3

Бренд: NAPCO Страницы: 4

Бренд: Auriol Страницы: 81

Бренд: GST Страницы: 2

Бренд: Geemarc Страницы: 11

Бренд: Deltronic Security Страницы: 9

ET-733 REDI CHEK

Бренд: Maverick Страницы: 2

Бренд: Datexx Страницы: 1

Бренд: Macurco Страницы: 4

Бренд: Visonic Страницы: 2

Бренд: Abus Страницы: 24

Бренд: Abus Страницы: 92

Бренд: Eurochron Страницы: 8

Бренд: Eurochron Страницы: 8

Бренд: brennenstuhl Страницы: 6

Бренд: Code Alarm Страницы: 20

Бренд: KRHÜNER Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды