CLIFFORD MATRIX 70.5X страница 30 Скачать руководство пользователя | Manualshive

Страница: 30 / 70

background image

© 2006 Directed Electronics—all rights reserved

30

PINK/WHITE (+) second ignition output

Connect this wire to the second ignition wire in the vehicle. (See

Finding the Wires You Need

section.)

NOTE:

For vehicles that do not have a second ignition wire, this connection is not required.

RED/WHITE (+) 12V input

Connection for high current outputs. The heavy gauge red/white wire serves the same function as the
heavy gauge red wires

remote start secondary harness (H3) wire connection guide

H3/1 BLACK/WHITE neutral safety switch input

Connect this wire to the provided toggle (override) switch as shown in figure A. Connect the other wire
from the toggle switch to the PARK/NEUTRAL switch in the vehicle. This wire will test with ground with the
gear selector either in PARK or NEUTRAL. This will prevent the vehicle from accidentally being started while
in a drive gear. This input MUST rest at ground in order for the remote start system to operate. Connected
properly the vehicle will only start while in PARK or NEUTRAL.

In some vehicles, the PARK/NEUTRAL position switch activates a factory starter lock out that will not allow
the starter to operate in a drive gear. In these vehicles, connect this wire to the toggle switch as shown in
figure B. Connect the other wire from the toggle switch to chassis ground.

IMPORTANT!

Always perform the Safety Check section of this installation guide to verify that the vehicl-

cannot be started in ANY drive gear and that the override switch is functioning properly.

«
...
28
29
30
31
32
...
»

Содержание 70.5X







































































Отзывы:

Нет отзывов

Похожие инструкции для 70.5X

Бренд: Yale Страницы: 2

Бренд: La Crosse Technology Страницы: 23

Бренд: Falcon Страницы: 10

Бренд: Casio Страницы: 2

KIDS ALC-KROBOT

Бренд: Laser Страницы: 13

Prestige APS-35-CL

Бренд: Audiovox Страницы: 19

Бренд: Kidde Страницы: 13

Бренд: Kidde Страницы: 17

Бренд: Kidde Страницы: 10

Бренд: Kidde Страницы: 48

Бренд: Kidde Страницы: 22

Бренд: Kidde Страницы: 16

Бренд: Kidde Страницы: 21

CS-2002DC Series III

Бренд: CrimeStopper Страницы: 21

Бренд: Ambient Weather Страницы: 10

Бренд: Eurochron Страницы: 8

Бренд: Bush Baby Страницы: 32

Бренд: SPAL Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды