CLIFFORD MATRIX 70.5X страница 64 Скачать руководство пользователя | Manualshive

Страница: 64 / 70

background image

© 2006 Directed Electronics—all rights reserved

4

troubleshooting

alarm troubleshooting

■

Shock sensor doesn't trigger the alarm:

Has the NPC® system been triggered? If so, you will hear 5 chirps when disarming. To check this,
turn the ignition key on and off to clear the NPC®'s memory, and then retest the shock sensor. For
a detailed description of NPC®, see

Nuisance Prevention Circuitry

section of this guide.

■

Door input does not immediately trigger full alarm. Instead, chirps are heard for the first 3

seconds:

That's how the progressive two-stage door input works! This is a feature of this system. This is an
instant trigger, remember, since even if the door is instantly closed again, the progression from chirps
to constant siren will continue.

■

Closing the door triggers the system, but opening the door does not:

Have you correctly identified the type of door switch system? This happens often when the wrong
door input has been used. (See

Door Lock Harness Wire Connection Guide

section of this guide.)

■

System will not passively arm until it is remotely armed and then disarmed:

Are the door inputs connected? Is the H1/6 blue wire connected to the door trigger wire in the
vehicle? Either the H1/5 green or the H1/7 violet should be used instead. (See wiring diagrams.)

■

Door input does not respond with the progressive trigger, but with immediate full alarm:

Does the Status LED indicate that the trigger was caused by the shock sensor? (See

Diagnos-

tics

section of this guide.) The shock sensor, if set to extreme sensitivity, may be detecting the

door unlatching before the door switch sends its signal. Reducing the sensitivity can solve this
problem.

■

The Valet/Program switch doesn't work.

Is it plugged into the correct socket? See

Plug-In LED and Valet/Program Switch

section of this

guide.

■

Status LED doesn't work.

You've probably guessed already, but here goes: Is it plugged in? (See

Plug-In LED and Valet/Program

Switch

section of this guide.) Is the LED plugged into the correct socket?

■

Door locks operate backwards.

This unit has easily-reversed lock/unlock outputs. Recheck wire connections to see if you have
reversed these.

«
...
62
63
64
65
66
...
»

Содержание 70.5X







































































Отзывы:

Нет отзывов

Похожие инструкции для 70.5X

Бренд: Bang & Olufsen Страницы: 20

Бренд: La Crosse Technology Страницы: 11

Бренд: La Crosse Technology Страницы: 18

Бренд: La Crosse Technology Страницы: 6

Бренд: La Crosse Technology Страницы: 12

Бренд: La Crosse Technology Страницы: 8

Бренд: La Crosse Technology Страницы: 23

Бренд: CYCLOPS Страницы: 8

Бренд: Code Alarm Страницы: 12

Бренд: ELRO Страницы: 2

Бренд: REV Ritter Страницы: 10

Бренд: Explore Scientific Страницы: 84

Бренд: Techno Line Страницы: 8

Бренд: stabo Страницы: 12

Бренд: Firex Страницы: 8

Бренд: Johnson Controls Страницы: 16

METASYS DH500 Series

Бренд: Johnson Controls Страницы: 32

Бренд: Universal Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды