manualshive.com logo in svg

CLIFFORD MATRIX 70.5X, Руководство по установке

Купите Clifford Matrix 70.5X - высокотехнологичную систему безопасности для вашего автомобиля. Для правильной установки и настройки устройства загрузите бесплатное руководство по установке с manualshive.com. Неотъемлемый помощник для вашего автомобиля.

Поделиться
Скачать
background image

table of contents

what  is  included.............................................5
warning!  safety  first.......................................5

installation points to remember........................6

before  beginning  the  installation......................6
after  the  installation.......................................7

deciding on component locations......................7

locations  for  the  siren.....................................7
locations  for  the  control  module.......................8
locations for stinger doubleguard shock sensor....8
mounting  the  antenna.....................................9
locations  for  valet/program  switch....................9
locations for the status LED.............................10
locations  for  the  relay  satellite.......................11

finding the wires you need.............................11

obtaining  constant  12V..................................11
finding the 12V switched ignition wire..............12
finding the starter wire..................................13
finding the accessory wire..............................14
finding the tachometer wire............................14
finding the wait-to-start bulb wire for diesels ..15
finding a (+) parking light wire.......................15
finding the door pin switch circuit...................16

making your wiring connections...................17
primary harness (H1), 12-pin connector.........18
auxiliary harness (H2), 6-pin connector.........18
door lock harness, 3-pin connector...................19
remote start ribbon harness, wiring diagram....19
heavy gauge inline connector key switch inter-
face........................................................20
remote start harness (H3), 5-pin connector.....20
horn, channel 6 (H4), 2-pin connector..............20
primary harness 6 (H1), wire connection guide..21
secondary harness 6 (H1), wire connection guide
.................................................................26
relay satellite wire connection guide................29
remote start secondary harness (H3) wire  
connection guide..........................................30

horn,  channel  6  harness  (H4)  wire  connection 
guide..........................................................33
neutral safety switch interface......................33

testing the neutral safety switch.....................34

vehicle immobilizer systems.........................36
plug-in LED and valet/program switch..............37
programmer interface, 3-pin black plug.............38
shock sensor harness, 4-pin connector..............38
tach learning................................................39
programming  jumpers...............................40

tach threshold on/off ....................................40
light flash (+)/(-)..........................................40

remote control learn routine™.......................41

standard  configuration...................................41

remote  control............................................44
remote control diagram................................45
remote control programming.........................46
system features learn routine........................48
feature  menus.............................................51

menu #1 - basic features................................51
menu #2 - advanced features...........................52
menu #3 - remote start options.......................53

feature descriptions.....................................54

menu #1 - basic features................................54
menu #2 - advanced features..........................55
menu #3 - remote start options.......................58

valet mode...................................................60
table of zones..............................................61
shutdown diagnostics...................................61

to perform shutdown diagnostics.....................61

long term event history.................................62
safety check................................................63
troubleshooting..........................................64

alarm  troubleshooting....................................64
remote start troubleshooting...........................65

wiring quick reference guide..........................67
relay satellite wiring quick reference guide.....68

Содержание 70.5X







































































Отзывы:

Нет отзывов

Похожие инструкции для 70.5X

Manta AVS 24v S Series Installation Manual preview
AVS 24v S Series
Бренд: Manta Страницы: 32
Emerald EP-RANG-10 User Manual preview
EP-RANG-10
Бренд: Emerald Страницы: 4
La Crosse Technology WT-2171 Instruction Manual preview
WT-2171
Бренд: La Crosse Technology Страницы: 5
OBH Nordica 4943 User Manual preview
4943
Бренд: OBH Nordica Страницы: 56
GE KM260 Series Installation And User Manual preview
KM260 Series
Бренд: GE Страницы: 13
Prestige APS-35 Owner'S Manual preview
APS-35
Бренд: Prestige Страницы: 20
By Firstech MA580 Installation Manual preview
MA580
Бренд: By Firstech Страницы: 14
TechniSat DIGITRADIO 50 SE Manual preview
DIGITRADIO 50 SE
Бренд: TechniSat Страницы: 204
Fire-Lite Alarms BG-12LPS Manual preview
BG-12LPS
Бренд: Fire-Lite Alarms Страницы: 2
Toyota RS3200 PLUS Owner'S Manual preview
RS3200 PLUS
Бренд: Toyota Страницы: 23
Black Widow Security RAS 200 Owner'S Manual preview
RAS 200
Бренд: Black Widow Security Страницы: 4
Xtralis XCC-010 Product Manual preview
XCC-010
Бренд: Xtralis Страницы: 36
Xtralis vesda LaserFOCUS VLF-500 Product Manual preview
vesda LaserFOCUS VLF-500
Бренд: Xtralis Страницы: 61
Clarion UNGO KE106 Owner'S Manual preview
UNGO KE106
Бренд: Clarion Страницы: 12
Clarion UNGO CS105 Owner'S Manual preview
UNGO CS105
Бренд: Clarion Страницы: 12
Clarion UNGO MS2007 Owner'S Manual preview
UNGO MS2007
Бренд: Clarion Страницы: 22
Clarion UNGO Pro Security S670 Owner'S Manual preview
UNGO Pro Security S670
Бренд: Clarion Страницы: 39
Eurochron EFW 221 Operating Instructions Manual preview
EFW 221
Бренд: Eurochron Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды