CLIFFORD MATRIX 70.5X Скачать руководство пользователя | Manualshive

Страница: 26 / 70

background image

© 2006 Directed Electronics—all rights reserved

2

H1/12 ORANGE (-) ground-when-armed output

This wire supplies a (-)500 mA ground as long as the system is armed. This output ceases as soon as the
system is disarmed. The GWA can be hooked up to a window control module, a voice module or any accessory
that requires a ground when armed.

secondary harness (H2) wire connection guide

H2/1 LIGHT BLUE (-) 200mA 2nd unlock output

This wire provides a second unlock output for progressive locks. Refer to document 1041—

Door Locking

System Wiring Guide

for specific applications.

H2/2 WHITE/BLACK 200 mA (-) programmable channel 5 output

This wire provides 200 mA programmable output. (See

Feature Descriptions

section of this guide.)

IMPORTANT!

Never use this wire to drive anything but a relay or a low-current input! This transistorized

output can only supply 200 mA, and connecting directly to a solenoid, motor, or other high-current device
will cause the module to fail.

H2/3 VIOLET/BLACK 200 mA (-) programmable channel 4 output

This wire provides 200 mA programmable output. (See

Feature Descriptions

section of this guide.)

IMPORTANT!

Never use this wire to drive anything but a relay or a low-current input! This transistorized

output can only supply 200 mA, and connecting directly to a solenoid, motor, or other high-current device
will cause the module to fail.

«
...
24
25
26
27
28
...
»

Содержание 70.5X







































































Отзывы:

Нет отзывов

Похожие инструкции для 70.5X

Бренд: La Crosse Technology Страницы: 6

Бренд: La Crosse Technology Страницы: 7

Бренд: jablotron Страницы: 2

Бренд: Brigade Страницы: 8

K9 CLASSIC-EDP2

Бренд: Omega Research & Development Страницы: 16

Бренд: La Crosse Technology Страницы: 13

SmartKey VSK100

Бренд: Viper Страницы: 2

Бренд: Datexx Страницы: 1

Бренд: Datexx Страницы: 1

Бренд: FireAngel Страницы: 68

Бренд: Abus Страницы: 108

Бренд: Abus Страницы: 124

Бренд: MGI Страницы: 32

World Time Alarm Clock with USB Hub RAS200

Бренд: Oregon Scientific Страницы: 2

Бренд: Oregon Scientific Страницы: 11

Бренд: La Crosse Technology Страницы: 20

Бренд: Radio Shack Страницы: 12

Бренд: Magicar Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды