CLIFFORD MATRIX 70.5X Скачать руководство пользователя | Manualshive

Страница: 63 / 70

background image

© 2006 Directed Electronics—all rights reserved

3

safety check

Before vehicle reassembly, the remote system must be checked to ensure safe and trouble-free operation.
The following test procedure must be used to verify proper installation and operation of the system. The
installation must be completed before testing, including connection to the brake switch and hood switch.
1. Test the BRAKE shutdown circuit: With the vehicle in Park (P), activate the remote start system. Once the
engine is running, press the brake pedal. The engine should shut down immediately. If the engine continues
to run, check the brake circuit connection.
2. Test the HOOD PIN shutdown circuit: With the vehicle in Park (P), open the hood. Activate the remote
start system. The vehicle should not start. If the starter engages, check your hood pin and connections.
3. Test the NEUTRAL SAFETY shutdown circuit:

IMPORTANT!

Make sure there is adequate clearance to the front and rear of the vehicle before attempting

this test.

a. Make sure the hood is closed and no other shutdown circuits are active.
b. Set the emergency brake.
c. Turn the ignition key to the run position but do not start the engine.
d. Put the vehicle in Drive (D).
e. Put your foot over the brake pedal but do not press down on it. Be ready to step on the brake to shutdown
the remote start system.
f. Activate the remote start system.

■

If the starter engages, immediately step on the brake to shut down the system. If it does engage,

recheck the neutral safety input connection. The vehicle may use a mechanical neutral safety switch. (See
H3/1 BLACK/WHITE neutral safety switch input in

Remote Start Harness Wire Connection Guide

section of

this guide.)

■

If the starter does not engage, the test is complete.

Once the system passes the three tests, the vehicle can be re-assembled and delivered. Do not the use the
remote start system or finalize the installation if it fails any of the safety check tests.

«
...
61
62
63
64
65
...
»

Содержание 70.5X







































































Отзывы:

Нет отзывов

Похожие инструкции для 70.5X

Бренд: Hama Страницы: 3

Innovair Flex D2E

Бренд: System Sensor Страницы: 6

Бренд: Carbine Страницы: 8

Бренд: CYCLOPS Страницы: 8

Бренд: Clifford Страницы: 14

Бренд: ELOTEC Страницы: 12

Prestige Platinum 128-4629B

Бренд: Audiovox Страницы: 21

Бренд: nest Страницы: 60

Бренд: Connect2Car Страницы: 8

Бренд: Abus Страницы: 80

Бренд: Abus Страницы: 234

Бренд: Quantum Guardian Страницы: 20

Бренд: brennenstuhl Страницы: 104

Бренд: Radio Shack Страницы: 1

Бренд: Teknim Страницы: 4

Бренд: Guanxing Photoelectric Products Страницы: 9

Бренд: Universal Electronics Страницы: 9

Бренд: DEI Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды