CLIFFORD MATRIX 70.5X Скачать руководство пользователя | Manualshive

Страница: 9 / 70

background image

© 2006 Directed Electronics—all rights reserved

vertically but range will be diminished. Metallic window tint can also affect range, so this should be a
consideration when determining the mounting location.
After determining the best mounting location, follow these steps:
1. Clean the mounting area with a quality glass cleaner or alcohol to remove any dirt or residue.
2. Mount the antenna using the supplied double-sided tape.
3. Route the antenna cable to the control module and plug it into the antenna connector.

IMPORTANT!

To achieve the best possible range, DO NOT leave the antenna cable bundled under the dash.

Always extend the cable full length during installation, regardless of the antenna mounting location.

locations for stinger doubleguard shock sensor

Some things to remember about where to mount the shock sensor:

■

Never put the Stinger

®

in the engine compartment!

■

Find a spot close to the control module so that the wires do not need to be extended. Keep it away from

the heater core (or any other heat sources) and any obvious leaks.
How the Stinger

®

is mounted is the most important factor in its performance. We recommend two methods:

■

Using double-sided tape or hook-and-loop fastener to mount to a trim panel or an air duct,

or

■

Wire-tying to a wire harness.

If mounting the sensor where it cannot be easily reached for adjustment, hook-and-loop fastening tape
(such as Velcro) is recommended for ease of removal for future adjustments.

NOTE:

In many vehicles, tying the sensor to a steering column or screwing it to metal will result in poor

sensitivity, especially at the rear of the vehicle.

locations for valet/program switch

IMPORTANT!

When the vehicle is delivered, please show the user where this switch is located and how to

disarm the system with it.

Ensure that the location you pick for the switch has sufficient clearance to the rear. The switch should be
well hidden. It should be placed so passengers or stored items (such as in a glove box or center console)
cannot accidentally hit it. The switch fits into a

9

/

32

-inch hole.

«
...
7
8
9
10
11
...
»

Содержание 70.5X







































































Отзывы:

Нет отзывов

Похожие инструкции для 70.5X

Klaxalarm Boxer

Бренд: Klaxon Страницы: 3

Бренд: Gentex Страницы: 6

Бренд: UltraFire Страницы: 27

Бренд: Clifford Страницы: 14

Бренд: Tytan Страницы: 20

Бренд: Cobra Страницы: 30

Бренд: AUTHOR Alarm Страницы: 12

Бренд: Datexx Страницы: 1

Бренд: Clas Ohlson Страницы: 3

Бренд: Xtralis Страницы: 2

Home 4 You ZHS20

Бренд: Schwaiger Страницы: 2

Бренд: HoMedics Страницы: 30

Бренд: E-Pill Страницы: 2

Бренд: XVision Страницы: 8

Бренд: La Crosse Technology Страницы: 8

Бренд: Code Alarm Страницы: 15

Бренд: La Crosse Technology Страницы: 12

Бренд: Incite Fire Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды