CLIFFORD MATRIX 70.5X Скачать руководство пользователя страница 52

Страница: 52 / 70

menu #2 - advanced features

FEATURE

NUMBER ONE-CHIRP SETTING (DEFAULT)

TWO-CHIRP SETTING

2-1*

30 second siren duration

60 second siren duration

2-2

Nuisance Prevention Circuitry ON

Nuisance Prevention Circuitry OFF

2-3

Progressive door trigger

Instant door trigger

2-4

Disarm from Valet, 1 pulse

Disarm from Valet, 2-5 pulses (2-5)

2-5

Door sensor bypass chirp ON

Door sensor bypass chirp OFF

2-6

Ignition controlled domelight ON

Ignition controlled domelight OFF

2-7

Unlock output 1 pulse

Unlock output 2 pulses

2-8

Lock output 1 pulse

Lock output 2 pulses

2-9

Factory disarm with Channel Two ON

Factory disarm with Channel Two OFF

2-10

FAD function with Unlock

(1)

Before Unlock (2) Remote Start only (3)

2-11

FAD 1 pulse

2 pulses

2-12

Channel 4 validity

(1)

Latched (2), Latch reset with ignition

(3), 30-sec. timed* (4)

2-13

Channel 4 linking None

(1)

Arm (2), Disarm (3), Remote Start (4)

2-14

Channel 5 validity

(1)

Latched (2), Latch reset with ignition

(3), 30-sec. timed* (4)

2-15

Channel 5 linking None

(1)

Arm (2), Disarm (3), Remote Start (4)

2-16

Channel 6 validity

(1)

Latched (2), Latch reset with ignition

(3), 30-sec. timed* (4)

2-17

Channel 6 linking None

(1)

Arm (2), Disarm (3), Remote Start (4)

NOTE:

The Bitwriter® can set 1-180 seconds.

Содержание 70.5X




































































Результаты поиска

Содержание 70.5X

Отзывы:

Бренды по названию

Популярные бренды

CLIFFORD MATRIX 70.5X, Руководство по установке

Результаты поиска

Содержание 70.5X

Отзывы:

Бренды по названию

Популярные бренды