CLIFFORD MATRIX 70.5X Скачать руководство пользователя

Страница: 51 / 70

feature menus

The default settings are indicated in

bold

type. Features that have additional settings that can be pro-

grammed using the Bitwriter® are indicated with an asterisk (*).

menu #1 - basic features

FEATURE
NUMBER ONE-CHIRP SETTING (DEFAULT)

TWO-CHIRP SETTING

1-1

Active arming

Passive arming

1-2

Arm/disarm chirps on

Arm/disarm chirps off

1-3

Ignition lock ON

Ignition lock OFF

1-4

Ignition unlock ON

Ignition unlock OFF

1-5

Active locking only

Passive locking

1-6

Panic with ignition on

No panic with ignition on

1-7

0.8 second door lock pulses (1)

3.5 (2), 0.4 (3) seconds

1-8

Forced passive arming on

Forced passive arming off

1-9

Automatic engine disable on

Automatic engine disable off

1-10

Armed When Driving (AWD) on

AWD off

1-11

Code Hopping on

Code Hopping off

1-12

Horn Output Pulsed

Constant

1-13

Horn function Full Alarm Only (1)

Siren function - chirp length

20mS (2)/30mS (3)/40mS (4)/50mS (5)

1-14 Comfort Closure ON

Comfort Closure OFF

NOTE:

The numbers in parentheses indicate the number of times the siren will chirp and the LED will flash.

Содержание 70.5X




































































Результаты поиска

Содержание 70.5X

Отзывы:

Похожие инструкции для 70.5X

Бренды по названию

Популярные бренды

CLIFFORD MATRIX 70.5X, Руководство по установке

Результаты поиска

Содержание 70.5X

Отзывы:

Похожие инструкции для 70.5X

Бренды по названию

Популярные бренды