CLIFFORD MATRIX 70.5X страница 43 Скачать руководство пользователя | Manualshive

Страница: 43 / 70

background image

© 2006 Directed Electronics—all rights reserved

43

4.

Transmit.

While

HOLDING

the Valet/Program switch, press the

button on the remote control that you would like to control the
selected function. The unit will chirp to confirm that the code has
been successfully programmed.
It is not possible to teach a remote control button to the system
more than once.

5.

Release.

Once the code is learned, the Valet/Program switch can

be released.

You can advance from one function step to another by releasing the Valet/Program switch and tapping it
to advance function steps and then

HOLDING

it. For instance: You have programmed function step 2 (Arm

Only) and you want to program function step 8 (Channel 6). Release the Valet/Program switch. Press it 6
times and release it to advance from function step 2 to 8. Now, press and

HOLD

the Valet/Program switch.

The LED will flash 8 times and the siren will chirp 8 times. As before, do not release it.

Learn Routine will be exited if:

■

Door is closed.

■

Ignition is turned off.

■

Program switch is pressed too many times.

■

More than 15 seconds between steps.

«
...
41
42
43
44
45
...
»

Содержание 70.5X







































































Отзывы:

Нет отзывов

Похожие инструкции для 70.5X

Бренд: NEAT Electronics Страницы: 16

Бренд: BALANCE TIME Страницы: 2

Smoke & CO Listener Z-Wave

Бренд: ring Страницы: 3

Бренд: Emerald Страницы: 4

Бренд: x-sense Страницы: 16

Бренд: Trevi Страницы: 5

Бренд: Trevi Страницы: 20

Бренд: Toyota Страницы: 23

Бренд: i-box Страницы: 60

Бренд: Shuoyu Technology Страницы: 6

Бренд: Dicon Страницы: 3

Бренд: QBA Страницы: 5

Бренд: Clas Ohlson Страницы: 10

Бренд: nest Страницы: 50

Бренд: Jacob Jensen Страницы: 16

Davy the dog SLEEPTRAINER

Бренд: ZAZU Страницы: 41

Бренд: Falcon Страницы: 11

Бренд: Zeon Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды