CLIFFORD MATRIX 70.5X Скачать руководство пользователя страница 42

Страница: 42 / 70

Function Step

Function

Wire Color

Auto Learn Standard Configuration

(default)

Arm only

Disarm only

Silent Mode™/Remote Valet/Trunk Release

RED/WHITE

Remote Start

Channel 4

VIOLET/BLACK

Channel 5

WHITE/BLACK

Channel 6

Short Run/Turbo

Timer Mode

Arm/Disarm/Panic

Panic only

Defogger Control**

Delete all remote controls***

*NOTE:

For Auto Learn Configurations, refer to the

remote control

section of this guide.

**NOTE

: The remote control will play Rear Defogger animation only when pressing the Rear Defogger button

configuration described in the

remote control

section

*NOTE:

If any button from a known remote control is programmed to function step 14, all remote

controls will be erased from memory and all features will revert to their default setting. This is useful
in cases where the customer's remote controls are lost or stolen.

Содержание 70.5X




































































Результаты поиска

Содержание 70.5X

Отзывы:

Бренды по названию

Популярные бренды

CLIFFORD MATRIX 70.5X, Руководство по установке

Результаты поиска

Содержание 70.5X

Отзывы:

Бренды по названию

Популярные бренды