CLIFFORD MATRIX 70.5X Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 70

CLIFFORD MATRIX 70.5X Скачать руководство пользователя страница 21

© 2006 Directed Electronics—all rights reserved

21

primary harness (H1) wire connection guide

H1/1 RED/WHITE channel 2, 200mA (-) output

When the system receives the code controlling Channel 2, for longer than 1.5 seconds, the red/white wire
will supply an output as long as the transmission continues. This is often used to operate a trunk/hatch
release or other relay-driven function.

IMPORTANT!

Never use this wire to drive anything but a relay or a low-current input! The transistorized

output can only supply 200 mA of current. Connecting directly to a solenoid, motor, or other high-current
device will cause it to fail.

H1/2 RED (+)12V constant power input

Before connecting this wire, remove the supplied fuse. Connect to the battery positive terminal or the
constant 12V supply to the ignition switch.

NOTE:

Always use a fuse within 12 inches of the point you obtain (+)12V. Do not use the 15A fuse in the

harness for this purpose. This fuse protects the module itself.

H1/3 BROWN (+) siren output

Connect this to the red wire of the siren. Connect the black wire of the siren to (-) chassis ground, preferably at the
same point you connected the control module’s black ground wire. See

Features Description

section

for horn outp

«
...
19
20
21
22
23
...
»

Содержание 70.5X







































































Отзывы:

Нет отзывов