CLIFFORD MATRIX 70.5X Скачать руководство пользователя | Manualshive

Страница: 24 / 70

background image

24

H1/10 WHITE/BLUE remote start (-) activation input

This input comes from the factory set to 2 activation pulses. This means that it is necessary to have 2
consecutive ground pulses on the white/blue wire for the remote start to activate or to deactivate. The
same holds true for the remote control activation when set to a two pulse setting it is necessary to press
the

button twice for the remote start to activate or deactivate.

NOTE:

The number of activation inputs can be programmed to 1 or 2 pulses. This setting affects both the

input wire and the remote control when operating the remote starter.

H1/11 WHITE (+/-) selectable light flash output

As shipped, this wire should be connected to the (+) parking light wire. If the light flash polarity jumper
under the sliding door is moved to the opposite position (see

Internal Programming Jumper

section of this

guide), this wire supplies a (-) 200 mA output. This is suitable for driving (-) light control wires in Toyota,

«
...
22
23
24
25
26
...
»

Содержание 70.5X







































































Отзывы:

Нет отзывов

Похожие инструкции для 70.5X

Бренд: First Alert Страницы: 5

Бренд: Autopage Страницы: 20

Бренд: Jensen Страницы: 22

Бренд: WOOX Страницы: 47

Бренд: Philips Страницы: 2

Бренд: Fire-Lite Страницы: 2

Бренд: Masterbuilt Страницы: 36

Бренд: Masterbuilt Страницы: 36

Бренд: Capehart Страницы: 5

Бренд: Nordic Start Страницы: 3

Combination Fire Smoke Dampers SSFSDR-511

Бренд: Greenheck Страницы: 2

No Flow Duct Smoke Detector

Бренд: Greenheck Страницы: 4

Бренд: La Crosse Страницы: 6

Бренд: Decotech Страницы: 48

Бренд: 2gig Technologies Страницы: 8

Бренд: family first Страницы: 3

Бренд: La Crosse Technology Страницы: 8

Бренд: Cavius Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды