background image

WIRING CONNECTIONS

 

If you are using a power supply, then decide which product will be 
the Master Unit of the system and connect a 9

-

24Vdc power supply 

as  shown  opposite.  This  connection  is  continued  through  to  every 
device on the system to supply power. This will normally be the CSA

-

FSU installed outside the washroom area. You can connect up to 10 

devices to the CSA

-

FSU as shown in the diagram opposite.

 

 

When any device generates an alarm condition, this will be relayed 
to  the  Master  Unit  which  will  also  generate  an  alarm  condition 
simultaneously. You can use any of the devices as a Master Unit, the 
diagram opposite is by way of example only.

 

 

Use  7  x  0.2mm  stranded  alarm  cable  for  all  the  connections

Once  the  wiring  is  complete  and  checked,  switch  on  the  power 
supply at the mains. Each device will provide a message stating how 
it is configured. If you have a gas (smoke) element, the device will 
flash its LED for 2 minutes to normalise.

 

 

DO NOT TEST THE DEVICE UNTIL THE FLASHING STOPS. 

Your system is now installed and running normally.

 

Use the above diagram to connect any of the SD Evolution products as a master unit to any of the satellite products.

 

 

SpeechPOD (Part No CSA

-

POD) is normally supplied with an 

on

-

board infra red PIR motion sensor as its detection device.

 

 

You  can  however  trigger  the  SpeechPOD  by  other  sources 
instead or in addition to the PIR motion sensor. Examples of 
these may be:

 

 

Door Contact, Pressure mat, alarm output from security, fire 
or  Building  Management  Systems,  or  any  other  device  that 
has a Clean or Volt Free Output.

 

 

Simply  connect  the  Normally  Open  (NO)  contact  across  the  TRIG  IN  and  GND  input.  Each  time  the  switch  closes, 
SpeechPOD  will  play  its  programmed message.  Remember,  SpeechPOD  can be  battery  operated  or  powered  from a  9

-

24Vdc power supply connected to the 9

-

24V IN and GND inputs.

 

 

For further information or assistance with our products, please contact our Technical Department by phone or email as 
detailed below.

 

PRODUCT INSTALLATION GUIDE

 

 

       FOR THE FOLLOWING PRODUCTS

 

Part No: CSA

-

POD24

 

Advanced SpeechPOD 

 

Voice Warning System

 

Part No: CSA

-

FGS24

 

Cig

-

Arrête® Combined Flame,

 

Smoke and SpeechPOD

 

Part No: CSA

-

FSV24

 

Cig

-

Arrête® Combined

 

Flame and SpeechPOD

 

Part No: CSA

-

FSU24

 

Cig

-

Arrête® Combined

 

Flasher & Sounder Unit

 

Part No: CSA

-

FGV24

 

Cig

-

Arrête® Combined

 

Flame & Smoke Detector

 

Part No: CSA

-

FOV24

 

Cig

-

Arrête® Flame Detector

 

With Voice Sounder

 

Part No: CSA

-

GOV24

 

Cig

-

Arrête® Smoke Detector

 

With Voice Sounder

 

Part No: CSA

-

GSV24

 

Cig

-

Arrête® Combined

 

Smoke & SpeechPOD

 

Part No: CSA

-

DUAL24

 

Advanced SpeechPOD Dual

 

Voice Warning System

 

Содержание CSA-POD24

Страница 1: ...A POD is normally supplied with an on board infra red PIR motion sensor as its detection device You can however trigger the SpeechPOD by other sources instead or in addition to the PIR motion sensor Examples of these may be Door Contact Pressure mat alarm output from security fire or Building Management Systems or any other device that has a Clean or Volt Free Output Simply connect the Normally Op...

Страница 2: ...trigger unwanted alarms 5 For SpeechPOD installations if the number of message plays is expected to be high consider using an external 9 24Vdc power supply to avoid draining of batteries RADIO COMMUNICATION SETUP Not applicable to 24Vdc models The radio communication modules if fitted only transmit alarm conditions from the Cig Arrête elements ie Flame and smoke sensors They do not transmit any PI...

Страница 3: ... floor to dry 10 mins to 60 mins After the time period SpeechPOD will return to its normal mode and time delays etc DELAY AFTER ACTIVATION PLEASE SELECT TIME DELAY SpeechPOD will play the selected message immediately sensing motion but will not play any message again for a time period which is selected by pressing the TIME DELAY button UP or Down Typically this function is used for infection contr...

Страница 4: ...W CIG ARRETE CONFIGURATION AND SETUP PROCEEDURE Once you have accessed the configuration menu by pressing and holding the Cig Arrête button you have access to all the functions relevant to your particular device All these functions are shown below but remember if you do not have a particular element e g Flame detector on the device you have purchased you will not be able to set the configuration m...

Отзывы: