GENERAL OPERATING PROCEEDURE
All our products whether Cig
-
Arrête® or SpeechPOD can only be operated by use of the CSA
-
IR2
Infra Red remote Control handset. The products have a number of advanced features to allow
the facility management team to change messages, flame and smoke sensitivity, volume and
timer functions when necessary. in addition, in SpeechPOD mode, the product can provide an
additional message to alert visually impaired personnel or visitors to potential risk or hazards
such as wet and slippery floors.
All the products carrying the suffix 24 are designed to be powered from a separate regulated 9
-
24Vdc power supply. Once powered, the products will then immediately power up and begin
normal operation.
On initial power up, your particular product configuration will provide a message, stating its current configura-
tion, which will be one of the following:
PART No CSA
-
FGS24
“This device is configured as Flame Detector, Smoke Detector, SpeechPOD”
PART No CSA
-
FGV24
“This device is configured as Flame Detector, Smoke Detector”
PART No CSA
-
FOV24
“This device is configured as Flame Detector”
PART No CSA
-
GOV24
“This device is configured as Smoke Detector”
PART No CSA
-
GSV24
“This device is configured as Smoke Detector, SpeechPOD”
PART No CSA
-
FSV24
“This device is configured as Flame Detector, SpeechPOD”
PART No CSA
-
POD24
“This device is configured as SpeechPOD”
PART No CSA
-
DUAL24
“This device is configured as SpeechPOD Dual”
PART No CSA
-
FSU24
“This device is configured as Combined Sounder Beacon”
Whichever message is played depending on the model number, the device will then begin to initialise and power
up. In the case of a smoke detector forming part of the product, the blue LED will begin to flash to indicate that
the product is normalising (learning its environment). For both flame detectors and SpeechPOD there is no exter-
nal indication until either a flame or motion is detected at which point the device will play its programmed mes-
sage.
GENERAL FUNCTIONS
Pressing the ON/OFF button will cause the device to turn either ON or OFF. You cannot access any of the
configuration menu or change any settings until you select the appropriate device type.
Pressing the SPEECHPOD button will select the configuration menu for the SpeechPOD element and the
device will list its current configuration and allow access to function buttons.
Pressing the CIG
-
ARRETE button will select the configuration menu for the Flame and Smoke Detection
elements and the device will list its current configuration and allow access to function buttons.
Once you have selected either SPEECHPOD or CIG
-
ARRETE, the specific function buttons are activated.
Pressing the VOLUME control either UP or DOWN will scroll through the available options. These are:
“Device Volume HIGH”
“Device Volume MEDIUM”
“Device Volume LOW”
CIG
-
ARRETE CONFIGURATION AND SETUP PROCEEDURE
Once you have accessed the configuration menu by pressing and holding the Cig
-
Arrête® button, you have access
to all the functions relevant to your particular device. All these functions are shown below, but remember if you
do not have a particular element (e.g. Flame detector) on the device you have purchased, you will not be able to
set the configuration menu for this element.
Pressing the LANGUAGE button UP or DOWN will scroll through the list of available languages and the
device will tell you which language is currently selected. The languages programmed by the factory are
as follows and once selected all the menu settings will be spoken in the selected language.
“ENGLISH” ; “FRANCAIS” ; “DEUTSCHE” ; ESPAŇOL ; AMERICAN ; OTHER
Pressing the MESSAGE button UP or DOWN will scroll through the list of available messages you have
programmed in the Cig
-
Arrête® folder on the SD Flash Card. You can program several messages in this
folder and use the MESSAGE button to select the particular message to be played in the event of a
smoking detection. Please note that whichever message you select will be played for an alarm event
from either the flame detector, or the smoke detector.
Pressing the FLAME button UP or DOWN will scroll through the FLAME SENSITIVITY options to allow the
device to be set up for the particular environment. Factory default setting is NORMAL. You can also
turn off the FLAME sensor by selecting OFF. The settings are as follows:
“HIGH” ; “MEDIUM HIGH” ; “NORMAL” ; “MEDIUM LOW” ; “LOW” ; “OFF”
Pressing the SMOKE button UP or DOWN will scroll through the SMOKE SENSITIVITY options to allow
the device to be set up for the particular environment. Factory default setting is NORMAL. You can also
turn off the SMOKE sensor by selecting OFF. The settings are as follows:
“HIGH” ; “MEDIUM HIGH” ; “NORMAL” ; “MEDIUM LOW” ; “LOW” ; “OFF”
Pressing the TRANSIENT button UP or DOWN will select either ON or OFF. The transient delay is nor-
mally used to filter out unwanted alarms due to lactose intolerance, which can upset the sensitive
detection elements. The factory default is OFF. The settings are as follows:
“ON” ; “OFF”
Pressing the MODE button UP or DOWN will scroll through the MODE options which for Cig
-
Arrête®
elements are MESSAGE REPEATS (the number of times that the device will play the message in alarm)
The factory default setting is ONE. The options available are set by pressing the TIME DELAY button.
Once you have pressed the MODE button above, you can press the TIME DELAY button UP or DOWN to
scroll through the MESSAGE REPEATS (the number of times that the device will play the message in
alarm) The factory default setting is ONE. The options available are:
“OFF” ; “ONE” ; “TWO” ; “THREE”
Once you have configured the Cig
-
Arrête® elements present on your device, press the CIG
-
ARRETE
button again to return to ‘RUN MODE’ which makes the device run normally and ready to generate
alarm conditions. On exiting the configuration mode the device will provide the following message:
“DEVICE CONFIGURED”
