manualshive.com logo in svg

CareFusion IVAC P6000, Техническое и сервисное руководство

Поделиться
Скачать
CareFusion IVAC P6000 Скачать руководство пользователя страница 17

Configuration and Calibration

P7000, P6000, TIVA, TCI & TIVA 17/106 

1000SM00012 Issue 8

General Options (251)

GENERAL OPTIONS MENU (Mode

l

 TIVA/Mode

l

 TCI & TIVA)  

Software version: V3R2

Option

Description

TIVA*

TCI 

&TIVA*

BACKOFF

Enable/Disable Backoff feature (feature where pump action reverses to release infusion 

system pressure build-up and minimise post occlusion bolus following a pressure 

alarm).

Enabled: Backoff feature ON (This does not apply when the pump is in TCI mode). 

Disabled: Backoff feature OFF. 

AC FAIL ALARM

Enable/disable AC Fail alarm (activated when AC power disconnected and pump 

operating on battery power). Enabled: AC Fail alarm ON. Disabled: AC Fail alarm OFF.

NEOI WARNING

Set the Near End Of Infusion (NEOI) warning time between 1 min. and 15 mins. (NEOI 

warning signals the syringe is almost empty allowing time to change syringe).

EOI POINT

Enable/disable Keep Vein Open at End of Infusion (KVO at EOI). Enabled: Pump will 

switch to run at the KVO rate 1.0ml/h (or the current set rate if this is lower) at the EOI 

point. Disabled: Pump will stop at the EOI point.

BEAM ALARM

Set the default beam occlusion alarm level between level 0 (L0) and level 7 (L7).

WEIGHT

Set a default patient weight between 0.1kg and 150kg. Factory default is 70kg.

PURGE RATE

Set the purge rate volume between 100ml/h and 500ml/h. (Rate used during PURGE 

operation).

HANDS FREE BOLUS

Enable/disable Bolus function in a 'hands-free' way—no need to hold down buttons 

during bolus infusion. (Bolus is a function which administers a controlled volume 

of fluid or drug at an increased rate). Enabled: Hands Free Bolus function allowed. 

Disabled: Hands Free Bolus function not allowed.

DEFAULT BOLUS

Set the default bolus value between 0.1ml and 25ml.

NURSE CALL

Enable/disable the Nurse Call feature (hardware feature which allows the pump to 

communicate with the hospital's nurse call system, typically linked to central nurse's 

station). Enabled: Nurse Call Hardware enabled. Disabled: Nurse Call hardware 

disabled.

NURSE CALL INVERTED

Enable/disable inversion of Nursecall hardware output. Enabled: Nurse Call hardware 

output is inverted. Disabled: Nurse Call hardware output normal.

COMMS PUMP ADDRESS

Set the communications address of the pump.

COMMS MONITOR ONLY

Enable/disable pump remote control via the comms link. Enabled: Control of pump 

via monitor only. Disabled: Remote control of pump via comms link allowed. Note that 

monitor control is always possible.

COMMS ODD PARITY

Enable/disable odd communication parity bit generation.

COMMS ASCII

Enable/Disable ASCII communications mode.

TCI

Enable/disable TCI option. Enabled: TCI option is activated (TCI hardware must be 

fitted). Disabled: TCI option not activated.

DISPLAY TCI DECREMENT 

TIME

If enabled, the display shows the TCI Decrement Time Icon (TCI hardware must be 

fitted).

Key:

 = available option

 = unavailable option

* 

For pumps with software versions earlier than version V3R2, the options may vary, or will not be 

available. Refer to the relevant IVAC® Syringe Pump 

DFU

 for comprehensive information.

Note: For default settings, refer to Appendix D, 'Configured Options and Drug Protocol Records'.

1.  Enter the access code 

251

 to display the 

CONFIGURATION MENU

.

2. Select 

GENERAL OPTIONS

 using the 

M

 keys and press the 

OK

 softkey. The 

GENERAL OPTIONS MENU 

is displayed:

Содержание IVAC P6000











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды