Cardin 200/BL224ESB, Руководство пользователя

Страница: 17 / 48

7
Collegamenti scheda base
CC242ESBBS
07-12-2004
DC0388
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
CENTRALINA 2 MOTORI CC CON ENCODER
(con 6 display a led - selezione a dipswitch )
B1
CS 1218 DC0355
P3
CTRL 30Vdc CMN CMN FTCI (N.C) TD (N.O) CMN CMN TC (N.O) TAL (N.O) TB (N.C)
LP LS
OUT 30Vdc
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
LC/CH2
P2
L4
L2
L3
R1
J4
4A
4A
L11
L9
L7
L6
L10 L8 L5
1
2
3
4
5
6
7
8
9
10
ON
DS1
CSER
F5
J3
29
28
27
CMN
EMRG 2
EMRG 1
D1
COLORE COLOUR CODE COLORATION
CABLAGGI CODE DES CÂBLAGES
Bl Blu Blue Bleu
Gr Verde Green Vert
Gy Grigio Grey Gris
Yw Giallo Yellow Jaune
KABELFARBEN COLORACIÓN
CABLEADOS
Bl Blau Azul
Gr Grün Verde
Gy Grau Gris
Yw Gelb Amarillo
Collegamento motori/encoder a 4 fili
Connecting motor/4-wire encoder
Branchement moteur/encodeur à 4 fils
Anschluss der Motor/Encoder mit 4 Drähten
Conexionado motores/encoder de 4 conductores
7 8 3 4 5 6 1 2 3 4 5 6 1 2
Yw Gy Gr Bl
ENCODER 1
Yw Gy Gr Bl
ENCODER 2
M1
M2
CMN ELS 12V CMN TA
(N.O)
FTCS (N.C)
TD
RA
PLP
LP
LS
FTCI
TFTI
TFTS
SAP
ELS
P1
F1
10
10
4A
4A
F3
F2
10
10
F4
4A
4A
30
31
J5
1 2 3
Pos.1
1 2 3
Pos.2
J2
L1
J1
MM
Terminal board connections
7 CMN common for all inputs and outputs
8
ELS
electric lock output (fed continuously)
2 Vdc
-
5 W
.
9-10 LC-CH2 potential free contact for the activation of the courtesy light
(separate power supply Vmax = 30 Vac/dc: Imax = A ) or the second
radio channel. Selection is carried out using jumper " J5 ".
11
CMN
common for all inputs and outputs
12 LP 24 Vdc 25 W output for warning lights
intermittent activation (50%), 2,5 W continuous activation
13
LS 24 Vdc 3 W
output for an indicator light
14 CMN common for all inputs and outputs
15 30 Vdc controlled output, powering external loads
()
16 CMN common for all inputs and outputs
17
30 Vdc
output, powering external loads ()
18 CMN common for all inputs and outputs.
19 TA (NO contact) opening button input
20 TC (NO contact) closing button input
21
TAL
(NO contact) limited opening button input
22 TD (NO contact) dynamic button input
23 CMN common for all inputs and outputs
24 TB (NC contact) stop button input (The opening of this contact inter-
rupts the cycle until a new movement command is given).
25 FTCS (NC contact) Safety and control devices in input. (stop photo-
electric cells). The opening of this contact will block all movement, until
the obstruction has been removed and the pause time has elapsed, due
to the safety device cutting in, the door will then continue moving in the
closing direction (only with automatic reclosing enabled).
26 FTCI (NC contact) Safety and control devices in input (photocells invert
the travel direction when an obstruction is detected). Opening this contact
will provoke a travel direction inversion during closure due to the cutting
in of the safety device.
27
EMRG2
(NO) emergency manoeuvre input 2
28 EMRG (NO) emergency manoeuvre input 1
29 CMN common for the emergency buttons
30 Inner conductor for radio receiver antenna (if an external antenna is
fitted use a coaxial type cable
RG58
with an impedance of
50 Ω
).
31 Outer conductor for radio receiver antenna
Note
()
The total of the 2 external device outputs must not exceed 0 W.
ALL UNUSED NC CONTACTS MUST BE JUMPED
and consequently the
security device test must also be deactivated ( FTCI , FTCS - Dip 7 and Dip
8 " OFF ") . If you want to activate the FTCI, FTCS test both the transmission
and receiver parts of the security devices must be connected to the binding
post marked "
CTRL 30 Vdc
". If the test is active there will be a 1 second
delay between the command transmission and movement of the gate/s.
Switch on the power and make sure that the indicator LEDs are in the fol-
lowing condition.
- L Power on ON
- L2 Battery charging OFF
(2)
- L3
Wrong battery connection
OFF
(3)
- L4 Transmitter code programming indicator OFF
- L5 Indicator for the blocking button " TB " ON
(4)
- L6 Indicator for the inverting photoelectric cells " FTCI " ON
(4)
- L7
Indicator for the stop photoelectric cells "
FTCS
"
ON
(4)
- L8 Indicator for the opening button " TA " OFF
- L9 Indicator for the closing button " TC " OFF
- L0 Indicator for the limited opening button " TAL " OFF
- L
Indicator for the sequential command "
TD/CH
"
OFF
Note
(2)
: This LED is " ON " when the battery is charging.
Note
(3)
: If this LED is " ON " invert the battery power cables immediately.
Note
(4)
: Check that the activation of the safety devices switches the cor-
responding LEDs off.
If the green power on LED "L" doesn't light up check the condition of the
fuses and the power cable connection at the transformer primary.
If
one or more of the safety LEDs do not light up
check the contacts of the
relative security devices and check that the unused safety device contacts
have been bridged.
B Signal buzzer " via radio " mode
CSER Serial connection (only for diagnostics)
D Six-segment LED display
DS Selection dip-switch
F 0A blade fuse
(5)
(motor power protection)
F2 0A blade fuse
(5)
(motor protection during battery operation)
F3 4A blade fuse
(5)
( 24V circuit protection)
F4 4A blade fuse
(5)
( 24V circuit protection during battery operation)
F5 4A blade fuse
(5)
(electric lock protection)
J
Battery connection
J2
Transformer secondary protection
J3 Enable transmitter memorisation via radio
J4
Radio channel selection
J5 Binding posts 9, 10 selection (courtesy light/CH2 via radio)
MM
Transmitter code memory module
P Programming button ( PROG )
P2
Transmitter code memorization button (
MEMO
)
P3 Transmitter code cancellation button ( DEL )
R
Radio frequency module,
433 MHz
for
S449
transmitters
Note
(5)
: These are automotive type blade fuses (max. voltage 58 V )