Canon Colorado M Series Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 378

background image

Source code

Introduction

The listed open source components are governed by different licenses. Some of the licenses
contain regulations regarding the provision of the pertaining source code.

Policy / Guidelines / Rules

If you would like to obtain a machine-readable copy of the source code of an open source
component, which is made available under applicable license terms, you may request such copy
of the source code by sending an e-mail to

[email protected]

indicating the following:

1. Name and version of the Canon Production Printing software you licensed.
2. Name and version of open source software modules contained in the above identified Canon

Production Printing software of which you legitimately would like to obtain the source code.

We will provide you with a find place where you can obtain a machine-readable copy of the
source code or we will deliver a complete machine-readable copy of the corresponding source
code of the respective open source software component, as available and as is, on a medium of
our choice which can be customarily used for software interchange. You may be required to pay
the cost incurred for the source code distribution, however, the cost will in no event excess the
cost incurred for physically performing the source code distribution.

Regulation notices

This offer is valid to anyone in receipt of this information.

«
...
2
3
4
5
6
...
»

Содержание Colorado M Series



























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Colorado M Series

Бренд: GCC Technologies Страницы: 14

Бренд: Oki Страницы: 40

Бренд: Oki Страницы: 16

SCX-4300 - SCX 4300 B/W Laser

Бренд: Samsung Страницы: 97

SCX 4828FN - Laser Multi-Function Printer

Бренд: Samsung Страницы: 151

SCX 4725FN - B/W Laser - All-in-One

Бренд: Samsung Страницы: 120

SCX 4500 - B/W Laser - All-in-One

Бренд: Samsung Страницы: 97

SCX 4200 - B/W Laser - All-in-One

Бренд: Samsung Страницы: 95

SCX 4500 - B/W Laser - All-in-One

Бренд: Samsung Страницы: 172

ProXpress M337x

Бренд: Samsung Страницы: 56

PROXPRESS M332 SERIES

Бренд: Samsung Страницы: 50

ML-2240 - 23 Ppm Mono Laser Printer

Бренд: Samsung Страницы: 82

Бренд: Samsung Страницы: 8

ML-1610 - B/W Laser Printer

Бренд: Samsung Страницы: 134

ML-1610 - B/W Laser Printer

Бренд: Samsung Страницы: 112

Бренд: Samsung Страницы: 128

Бренд: Samsung Страницы: 152

ML 3471ND - B/W Laser Printer

Бренд: Samsung Страницы: 207

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды