Canon Colorado M Series Скачать руководство пользователя страница 146 | Manualshive

Страница: 146 / 378

background image

Print double-sided with automatic cut

Introduction

Colorado M-series offers the possibility to print on the inside as well as on the outside of the
media, which indirectly provides the user a way to print double-sided. For this you need the
license Print inside and double sided.

To print double-sided you print on the inside of the media.

How to print double-sided

Before you begin

RIP

• In [Media Characteristics], set automatic advance correction (AAC) to [Enhanced] to achieve an

optimal x-registration.
AAC prints yellow, white, or black markers on the media that the printer uses as guidance to
optimize the media step accuracy. See "Change the media settings" in the operation guide.

• In [Placement strategy]

→

[General], make sure that the left and right are identical.

• In [Placement strategy]

→

[Options], make sure that the space between copies values are 0.

Printer

• Use the tension bar (locked).

In case the media is normally (single-sided) printed without tension bar, switch to the locked
tension bar mode.
You can change this tension bar setting for the media type in the RIP. Change from [No tension
bar] to [Locked tension bar].

• Use a matte print mode, preferably the same mode for both sides.
• Do not enable automatic media advance or moist sensitivity settings.
• If necessary calibrate the media.

Tools

• A media suitable for double sided printing.
• 2 empty cores with the same width as the media you want to use.
• A roll of tape.

Print double-sided with automatic cut

146

Chapter 4 - Handle the media

«
...
144
145
146
147
148
...
»

Содержание Colorado M Series



























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Colorado M Series

Бренд: TDT Страницы: 15

WORKCENTRE 5050

Бренд: Xerox Страницы: 186

7500DX - Phaser Color LED Printer

Бренд: Xerox Страницы: 5

Бренд: DNP Страницы: 2

wematter Atmosphere

Бренд: 3D Systems Страницы: 11

Бренд: Oki Страницы: 192

DocuPrint 4050 NPS

Бренд: Xerox Страницы: 248

DocuPrint C2535 A

Бренд: Xerox Страницы: 120

WorkCentre WC7545

Бренд: Xerox Страницы: 8

Бренд: Xerox Страницы: 109

Бренд: Paradise POS Страницы: 275

ID MAKER Zenius

Бренд: IDVille Страницы: 66

Бренд: GCC Technologies Страницы: 80

VersaLink C9000

Бренд: Xerox Страницы: 255

Бренд: Xerox Страницы: 2

VORON BELT 350 KIT

Бренд: ADITIVA 3D Страницы: 27

Бренд: Loadrite Страницы: 12

Бренд: Infotec Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды