Canon Colorado M Series Скачать руководство пользователя страница 367 | Manualshive

Страница: 367 / 378

background image

•

CDRH regulations

This machine is certified as a Class 1 Laser product under Radiation Performance Standard
according to the Food, Drug and Cosmetic Act of 1990. Compliance is mandatory for Laser
products marketed in the United States and is reported to the Centre for Devices and
Radiological Health (CDRH) of the U.S. Food and Drug Administration of the U.S. Department
of Health and Human Services (DHHS). This means that the device does not produce
hazardous laser radiation. The related label indicates compliance with the CDRH regulations
and must be attached to laser products marketed in the United States.

CAUTION

Use of controls, adjustments or performance of procedures other than those specified in this
User Documentation may result in hazardous radiation exposure. This is a semiconductor
laser. The maximum power of the laser diode is

0.78 mW

.

Lamps (All countries)

• This product may contain lamps that are only intended for use in combination with and for this

specific product (and related equipment) and such lamps are not intended for use in other
applications.

Battery labeling (EEA including Switzerland)

• This product contains a battery. Please do not remove the battery. If the battery needs

replacement, this should be done only by skilled service technicians who are aware of the
removal instructions provided by Canon Production Printing.

• This product contains a battery or batteries. It (They) is (are) located in (a) printed circuit

board(s) that is (are) essential for the continuous error-free functioning of the product. The
battery or batteries should be removed only by skilled service technicians who are aware of the
removal instructions provided by Canon Production Printing.

Location

Battery capacity [mAh]

Contains

Internal controller

200

Lithium

Chapter 10 - Regulation Notices

367

«
...
365
366
367
368
369
...
»

Содержание Colorado M Series



























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Colorado M Series

Бренд: QMS Страницы: 27

Бренд: QMS Страницы: 3

Бренд: Kyocera Страницы: 157

imageRUNNER ADVANCE DX C478iZ

Бренд: Canon Страницы: 208

imageRUNNER ADVANCE DX C477iFZ

Бренд: Canon Страницы: 92

Бренд: Lanier Страницы: 234

Magicolor 2530 DL

Бренд: Konica Minolta Страницы: 10

Бренд: MIMAKI Страницы: 28

Digital Minilab Frontier LP5700R

Бренд: FujiFilm Страницы: 2

ZPS3611 - QUICK

Бренд: Zonet Страницы: 1

Бренд: Olivetti Страницы: 315

Бренд: Seiko Epson Страницы: 301

Бренд: Kyocera Страницы: 410

Бренд: Oki Страницы: 2

Бренд: Canon Страницы: 8

Бренд: Canon Страницы: 58

Бренд: Canon Страницы: 110

MultiPASS MP360

Бренд: Canon Страницы: 162

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды