Brocade Communications Systems Fabric OS v7.0.1 Скачать руководство пользователя страница 687 | Manualshive

Страница: 687 / 1132

background image

Fabric OS Command Reference

661

53-1001764-01

portCfgISLMode

2

portCfgISLMode

Enables or disables ISL R_RDY mode on a port.

SYNOPSIS

portcfgislmode

[

slot

/]

port

,

mode

DESCRIPTION

Use this command to enable or disable interswitch link read-ready (ISL R_RDY) mode on a port. Use the

portCfgShow

command to determine whether ISL R_RDY mode is enabled on a port.

In ISL R_RDY mode, the port sends a primitive signal that the port is ready to receive frames. The port
sends an exchange link parameter (ELP) with flow control mode 02. If a port is ISL R_RDY enabled, it
can only receive an ELP with flow control mode 02. A received ELP with flow control mode 01 will
segment the fabric.

This mode cannot detect any inconsistencies in fabric operating mode parameters, such as the PID
format of connected ports. Before enabling ISL R_RDY mode, ensure that all fabric-wide parameters are
consistent for every switch in the fabric.

Use

configShow fabric.ops

to view a complete listing of fabric operating mode parameters on the

switch.

The following E_Port configurations are not applicable to a port configured for ISL R_RDY mode. If
configured, these port configuration parameters are ignored during E_Port initialization:

•

Trunk port

•

VC link init

The

portCfgISLMode

and

portCfgLongDistance

levels LE, LD, or LS only can be enabled at the same

time. Such an ISL uses R_RDY mode of flow control over the long distance link. This feature is not
backward compatible with firmware versions that do not support it.

NOTES

Changes made by

portCfgISLMode

are persistent across switch reboots and power cycles.

This configuration can be cleared but not set on VE/VEX_Ports.

The execution of this command is subject to Virtual Fabric or Admin Domain restrictions that may be in
place. Refer to Chapter 1, "Using Fabric OS Commands" and Appendix A, "Command Availability" for
details.

The Fabric OS port configuration commands are not supported on FCoE ports.

OPERANDS

This command has the following operands:

slot

For bladed systems only, specify the slot number of the port to display, followed by
a slash (/).

port

Specify the port to display, relative to its slot for bladed systems. Use

switchShow

to list valid ports.

mode

Specify 1 to enable ISL R_RDY mode. Specify 0 to disable ISL R_RDY mode.

EXAMPLES

To enable ISL R_RDY mode on a port:

switch:admin>

portcfgislmode 1/3, 1

ISL R_RDY Mode is enabled for port 3. Please make sure

the PID formats are consistent across the entire fabric.

«
...
685
686
687
688
689
...
»

Содержание Fabric OS v7.0.1













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Fabric OS v7.0.1

PowerShot SX1 IS

Бренд: Canon Страницы: 48

Бренд: Canon Страницы: 2

Бренд: Samsung Страницы: 7

DRAGON NATURALLYSPEAKING ESSENTIALS

Бренд: Dragon Systems Страницы: 26

MOBILE SECURITY 2010 FOR ANDROID

Бренд: F-SECURE Страницы: 20

DEVICE FILTER MAC

Бренд: FARONICS Страницы: 30

Бренд: Southern Company Страницы: 13

Ohioedge CRM+BPM

Бренд: Source Technologies Страницы: 36

Web-based Management Utility

Бренд: Supermicro Страницы: 64

Over Loud Guitar FX Plug-in Suite

Бренд: Focusrite Страницы: 8

Бренд: Xerox Страницы: 60

MEDIASTUDIO PRO 7.0 - HD PLUG-IN 2.0

Бренд: Ulead Страницы: 11

B DLTSAGE INTEGRATION

Бренд: Tandberg Data Страницы: 36

Бренд: Harman Kardon Страницы: 19

Stylus pro 3800 portrait edition

Бренд: Epson Страницы: 12

Stylus Pro 5500

Бренд: Epson Страницы: 2

Stylus Pro 4800 Portrait Edition

Бренд: Epson Страницы: 6

Stylus Pro 4800 Portrait Edition

Бренд: Epson Страницы: 396

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды