manualshive.com logo in svg

Black Box 5000 MX215C, 5000 MX218C, Руководство пользователя

Поделиться
Скачать
Black Box 5000 MX215C, 5000 MX218C Скачать руководство пользователя страница 90

Multiserver 5000

88

Table 9-3. Sync Channel Characteristics (continued)

Option

Protocol

Default

Description

Number of

ASCII Bisync

1

Sets the number of leading pad characters to be

Leading Pad

EBCDIC Bisync

1

transmitted at the start of the block. This is used

Characters*

H-P Sync

1

for a time delay (1-9).

RTS/CTS

3

Sync-Pad

1

Number of

ASCII Bisync

1

Sets the number of trailing pad characters to be 

Trailing Pad

EBCDIC Bisync

1

transmitted at the end of the block. External device 

Characters*

H-P Sync

1

will have time to recognize the end of a block.

RTS/CTS

3

Sync-Pad

1

Buffer 

DLC

NONE

Used to regulate data transmission from a device

Control

ASCII Bisync

NONE

attached to the port. The default setting (NONE)

EBCDIC Bisync

NONE

removes all buffer control. When this option is 

H-P Sync

NONE

configured to CTS, the Multiserver will delay the 

RTS/CTS

NONE

CTS signal up to 250 milliseconds for buffer control.

Sync-Pad

NONE

MICOM DLC

NONE

MICOM Voice

NONE

Encoding

DLC

NRZ

Depending upon attached device, select NRZ or
NRZI. 

Idle Fill

DLC

FLAG FILL

There are four Idle Fill options. Selection depends
upon attached equipment:
• 

Mark Fill

sets an idle pattern of binary 1s between

DLC frames. Use this for IBM 3270 SDLC half-
duplex operation.
• 

Fall Fill

sets the idle pattern of hexadecimal 7E

(flag) between DLC frames.
• 

Auto Fill

and 

A128 Fill

automatically adjust idle

between DLC frames to 

mark

at the end of the

transmission, or 

flag

when the transmission is not

finished. For IBM AS/400 5250 SDLC operation, set
to either 

Auto Fill

for Modulo 8 or 

A128 Fill

for

Modulo 128 frame sequencing.

Clock Flow

DLC

ENABLE

When Clock Flow Control is enabled, the local 

Control

ASCII Bisync

ENABLE

Multiserver controls flow on the local port if the 

EBCDIC Bisync

ENABLE

Channel Clocking Option has been set to 

H-P Sync

ENABLE

RX-Internal. It does this by halting the channel’s 

RTS/CTS

ENABLE

clock. If NONE is chosen, there is no local data flow 

Sync-Pad

ENABLE

control. The data is discarded, and it is up to the 

MICOM DLC

ENABLE

remote Multiserver to issue a retransmit request.

* Prompt only. No menu.

Содержание 5000 MX215C, 5000 MX218C













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды