Black Box 5000 MX215C, 5000 MX218C Скачать руководство пользователя страница 73

Страница: 73 / 268

CHAPTER 8: Link Configuration

8.4 Port Configuration

Before the link is installed, the port assigned to the
link must be configured. Configure the port after
the local node is named (see

Section 6.6, Name the

Local Node

). The Port Configuration Menu is

accessed from the Configure Local Nodes Menu.

When you request the Port Configuration Menu,
the following prompt appears on the screen:

Enter the node ID/port number. Example:

NEWYORK/A2<cr>

The Port Configuration Menu then appears:

Only options 3, 4, and 5 relate to configuring and
installing a link.

The CCM port’s default varies depending on the
port number. See Table 8-1 for the correct default
and options for each port on the CCM.

Important

The Multiserver must be node-reset (to
current configuration) after each port
configuration is complete.

COMMAND FACILITY MAIN MENU [node id]

CONFIGURE LOCAL NODES

CONFIGURE LOCAL NODES [node id]

PORT CONFIGURATION

ENTER NODE-ID/CHANNEL #

(^X TO ABORT):

PORT CONFIGURATION [xxx]

1. ASYNC

2. SYNC

3. INTERCONNECT LINK

4. MUX LINK

5. X.21 LINK

CR - ACCEPT ENTRY

M - MAIN MENU

ENTRY:

Table 8-1. Multiserver 5000 CCM Default Port Configurations

Port (Channel)

Default

Number

Configuration

Possible Configurations

Interconnect Link

Interconnect Link, Mux Link, or X.21 Link

A2 and A3

Async Channel

Interconnect Link, Mux Link, X.21 Link, Sync Channel,
or Async Channel

A4 and A5

Async Channel

Mux Link, X.21 Link, Sync Channel, or Async Channel

Async Channel

Sync Channel or Async Channel

Содержание 5000 MX215C, 5000 MX218C












































































































































































































































































Результаты поиска

Содержание 5000 MX215C, 5000 MX218C

Отзывы:

Бренды по названию

Популярные бренды

Black Box 5000 MX215C, 5000 MX218C, Руководство пользователя

Результаты поиска

Содержание 5000 MX215C, 5000 MX218C

Отзывы:

Бренды по названию

Популярные бренды