manualshive.com logo in svg

Black Box 5000 MX215C, 5000 MX218C, Руководство пользователя

Поделиться
Скачать
Black Box 5000 MX215C, 5000 MX218C Скачать руководство пользователя страница 103

CHAPTER 9: Data-Channel Configuration

101

E

XTENDED

F

EATURES

The Extended Features Menu is accessed from the
Async Channel Menu as option 3.

The current configuration for each menu option is
displayed in brackets. Each of these features is
explained in 

Table 9-12

.To return to the previous

menu (

ASYNC CHANNEL 

Menu), enter a 

P

.

Table 9-12. Asynchronous Channel Extended Features

Option

Default

Description

1.

Data Compression

Enable

Selects whether compression will be enabled. When compression is
enabled, the Multiserver compresses a block of data when transmitting
and decompresses the data when receiving. Adaptive Huffman
Compression algorithms are used, so fewer bytes are required for the
transfer. Thus, throughput is increased. Both local and remote ports must
be configured for data compression before the channel will support
compression. When compression is disabled, the data transfers at normal
(slower) rates.

2.  Remote CTS 

Forced On

Allows the remote CTS signal to be strapped or transparent. The 

Control

selection depends on the device attached to the port.

Select 

Forced On

when the channel is forced connected and the port is

connected to a DTE device. Remote CTS will always be high. 

Select 

Normal

when a channel is forced connected and the port is connec-

ted to a DCE device. CTS will be controlled by Pin 11 of the local port.

When configuring a feeder mux, this option will not display.

ASYNC CHANNEL

EXTENDED FEATURES

3

EXTENDED FEATURES [node id/ch #]

1. DATA COMPRESSION

[ENABLE]

2. REMOTE CTS CONTROL

[FORCED ON]

CR - ACCEPT ENTRY

M  - MAIN MENU  P - PREVIOUS MENU

ENTRY:

Содержание 5000 MX215C, 5000 MX218C













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды