manualshive.com logo in svg

Black Box 5000 MX215C, 5000 MX218C, Руководство пользователя

Поделиться
Скачать
Black Box 5000 MX215C, 5000 MX218C Скачать руководство пользователя страница 225

Appendix D:  Messages

223

CHANNEL NOT INSTALLED

Info

An attempt has been made to configure or test a
voice/fax port and the port number selected is not a
voice/fax port.

CHANNEL(S) NOT

Info

An attempt has been made to view the status

INSTALLED

or configuration of a range of ports that are not
voice/fax ports.

CHANNEL REQUEST UNSUCCESSFUL,

Info

The voice/fax port you are trying to test is

PLEASE RETRY

not working properly.

CHECK FOR PROPER

Info

The selection entered required either a CSU/DSU

DEVICE INSTALLATION

module.  You have entered the wrong link number.

ni

CMOS ERROR

Alarm

There is a problem detected in writing to the
Multiserver configuration area.  Contact your service
representative.

COMMAND FACILITY

Info

The Command Facility Main Menu cannot be

DISABLED

accessed by the port requesting it.

COMMAND INHIBITED

Info

The password entered does not permit

BY PASSWORD

access to the selected menu.  (The password is a
status type rather than global type and permits
access only to view, status, and disconnect
functions.)

COMMAND MODE

Info

All available ports to the Command Mode

PORTS BUSY

are busy.  Up to two ports and the dedicated
Command Port (on the NMS Module) can access
the Command Mode at one time.

CONFIGURATION INHIBITED

Info

Async or sync port configuration is being

WRONG CHANNEL TYPE

attempted, but the channel number selected is
for a port of a different channel type.

CONFLICT IN

Info

An attempt has been made to copy channel

CHANNEL TYPES

parameters of two dissimilar channel types.

CONNECT 

n/c n/c cl

Event

Indicates the pair of ports that have been
connected and the called port’s class.  Also
indicates a force-connection has been made.

CONNECT FAIL

Info

Unable to connect to the remote Command Facility
from the local Command Facility.

Screen Display Messages

Message

Message Type

Explanation

Содержание 5000 MX215C, 5000 MX218C













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды