manualshive.com logo in svg

Black Box 5000 MX215C, 5000 MX218C, Руководство пользователя

Поделиться
Скачать
Black Box 5000 MX215C, 5000 MX218C Скачать руководство пользователя страница 149

CHAPTER 11: Administration

147

Table 11-7.  Status/Statistics (continued)

Option

Description

2.

Channel Status
(continued)

3.

Interface Status

This option is used to view the states of the control signals of a single data channel on
the local Multiserver. When you select this option, the following prompt appears:

ENTER CHANNEL # (^X TO ABORT):

Enter the data channel number. Press 

<cr>

. The Interface Status displays.

[node id] CHANNEL STATUS

CONNECTED

CH    STATUS   SPEED     TO NODE/CHAN

-------------------------------------

A04   FCONN    2400      xxxxxxxx/xxx

A05   CONN     9600      xxxxxxxx/xxx

A06   IDLE     9600      

ENTER CARRIAGE RETURN TO CONTINUE

CH

= Channel number

STATUS

CONN

= Connected

IDLE

= Idle

OOS

= Out of service

QUEUED = Queued, waiting for

the next available
channel in that
class

CIP

= Connection in

process

FCONN

= Force-connected

SPEED

= Data Rate

CONNECTED

= The node ID/

TO

channel # where 

NODE/CHAN

the channel is
connected

[node id/ch #] INTERFACE STATUS

TO NODE                  FROM NODE

---------------          --------------

RTS      (HIGH)          CD      (HIGH)

DTR      (HIGH)          DSR     (HIGH)

BUSY     (LOW)           RI      (LOW)

PIN 11   (HIGH)          CTS     (HIGH)

ENTER CARRIAGE RETURN TO CONTINUE

NOTE:

For Link ports, the FROM NODE column is listed first;
the TO NODE is listed second.

Содержание 5000 MX215C, 5000 MX218C













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды