manualshive.com logo in svg

Black Box 5000 MX215C, 5000 MX218C, Руководство пользователя

Поделиться
Скачать
Black Box 5000 MX215C, 5000 MX218C Скачать руководство пользователя страница 85

CHAPTER 9: Data-Channel Configuration

83

9.2  Synchronous Channels

Sync is supported only when directly attached to a
Multiserver. Feeder muxes can only support async
or voice channels.

Sync channels are not switchable and must be force
connected. Refer to 

Section 10.4, Synchronous

Connections

.

Unless you have the optional NMS installed, you
must leave one port configured for async (to access
the Command Facility).

P

ROTOCOL

M

ENU

Configure the port for sync. 

The following protocol menu will appear:

Select a channel protocol from the menu. 

Table 9-1

explains each option. Pressing 

M

will abort

the process. 

After you have selected the appropriate protocol,
the

CONFIGURE LOCAL NODES 

menu will

reappear. You may continue to configure data ports
as either sync or async. 

Important

Once you have completed your port
configurations, you must do a node
reset using the current configuration
option.

Until the Multiserver has been node-reset, you will
not be able to set any sync channel parameters.

If you change sync protocols, be sure to configure
both ends of the channel with the same protocol.
Do a node reset on both the local and remote
Multiserver units. (When changing protocol, the
channel cannot be connected.)

S

YNC

C

HANNEL

P

ARAMETERS

To continue with the sync configuration process,
select option 3, Sync Channel, from the Configure
Local Nodes Menu. 

The screen will display the following prompt:

Enter the node ID/channel number followed by a
carriage return to accept the entry. 

If you see 

CONFIGURATION INHIBITED

and 

WRONG

CHANNEL TYPE

messages, the port you have chosen

is not configured as a sync channel. It is likely that a
node reset (to current configuration) was not

PORT CONFIGURATION [xxx]

SYNC

2

CONFIGURE LOCAL NODES

SYNC CHANNEL

3

ENTER NODE-ID/CHANNEL # 

(^X TO ABORT):

SET CHANNEL PROTOCOL [DLC]:

1. DLC

2. ASCII BISYNC

3. EBCDIC BISYNC

4. H-P SYNC

5. RTS/CTS

6. SYNC-PAD

7. MICOM DLC

8. MICOM VOICE

9. FAST PACKET

10. TDM

CR - ACCEPT ENTRY

M  - MAIN MENU

ENTRY:

Содержание 5000 MX215C, 5000 MX218C













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды