manualshive.com logo in svg

Black Box 5000 MX215C, 5000 MX218C, Руководство пользователя

Поделиться
Скачать
Black Box 5000 MX215C, 5000 MX218C Скачать руководство пользователя страница 126

Multiserver 5000

124

10.9  Connect Protocol Details

Connect protocol is option 1 of the Switching
Parameters menu.   There are three connect
protocol options:  Dedicated, Auto, and DTR.  A
discussion of the protocols and how to configure
them is in 

Section 10.7, Asychronous Channel

Switching Parameters

, and 

Table 10-2

.  This section

discusses how the call request, completion, and
disconnect sequences operate for the dedicated,
auto-answer, and DTR protocols.

Definitions

:

Calling

port:

Receive Inhibit

=

on

Call Inhibit

=

off

Receiving

port:

Receive Inhibit

=

off

Call Inhibit

=

on

Dual

port:

Receive Inhibit

=

off

Call Inhibit

=

off

NOTE:  The 

Dual

port is both a calling and receiving

port.

D

EDICATED

P

ROTOCOL

Call Request

(

Calling

and 

Dual

port)

Idle State:

Multiserver holds DSR, CTS, and
CD 

high

.  RI is held 

low

.

•

Data activity automatically triggers a call
request.

or

•

If ABR (auto baud rate) is enabled, type

<cr>

to trigger a call request (see

Section 9.3, Asychronous Channels

).

Call Completion

(

Receiving

and 

Dual

ports)

No indication of call completion unless
the called port is an ABR port.  Then the
port is set to the calling port’s speed, and
the sign-on character is forwarded.

Disconnect Sequence

(

Calling

, 

Receiving,

and 

Dual

ports

Calling

port:

1. Device initiates

<break><break><break>

.

2. Multiserver sends 

DISCONNECTED

message.

Receiving

port

1. Device initiates

<break><break><break>

.

2. No indication of disconnection.

DTR P

ROTOCOL

Call Request

(

Calling

and 

Dual

ports)

Idle State:

DTR can be 

high

or 

low

.

Multiserver holds DSR, CTS, CD,
and RI 

low

.

1. Device raises or toggles DTR.

2. Multiserver then raises DSR, CTS, and

CD.

3. If ABR is enabled, 

<cr> 

should now be

typed (see 

Section 9.3, Asychronous

Channels

).

Call Completion

For 

Receiving

port

Idle State:

DTR must be 

high

, otherwise the

port is put out of service (OOS). In
either case, the Multiserver holds
DSR, CTS, CD, and RI 

low

.

1. Multiserver raises DSR, CTS, and CD.

2. No response is required from the device.

3. If ABR is enabled, then 

<cr>

will be

forwarded.

Содержание 5000 MX215C, 5000 MX218C













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды