manualshive.com logo in svg

Black Box 5000 MX215C, 5000 MX218C, Руководство пользователя

Поделиться
Скачать
Black Box 5000 MX215C, 5000 MX218C Скачать руководство пользователя страница 241

Appendix E:  Indicators

239

Appendix E:  Indicators

A6 A5 A4 A3 A2 A1

AT BO

Figure E-1.  CCM Indicator Positions.

CCM LED

Indicator

Indicator

Definition

Off

Flashing

On

AT

Active Mode

Indicates a fault or 

The unit is in a loopback

Normal operation

test condition

test mode

BO

Buffer Overflow

Buffer utilization is

Buffer utilization 

Data has been lost 

normal

exceeding 87%

because of a buffer 
overflow

A1

Port A1

Error-free data is

High error rate on link

Receiving own transmit

passing through 

or synchronization 

data; modem is in 

the link

has been lost with the

loopback

remote unit on the link

A2*

Port A2

No data activity

Data activity

Data activity

A3*

Port A3

No data activity

Data activity

Data activity

A4*

Port A4

No data activity

Data activity

Data activity

A5*

Port A5

No data activity

Data activity

Data activity

A6*

Port A6

No data activity

Data activity

Data activity

* If configured as a link, the indicator values are the same as for A1.

NOTE:  The indicator on a force-connected sync port using either

Fast Packet or TDM protocols will remain 

on

continuously.

Table E-1.  CCM Indicators.

Содержание 5000 MX215C, 5000 MX218C













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды