manualshive.com logo in svg

Black Box 5000 MX215C, 5000 MX218C, Руководство пользователя

Поделиться
Скачать
Black Box 5000 MX215C, 5000 MX218C Скачать руководство пользователя страница 48

Multiserver 5000

46

5.5.4  R

EMOVE

S

PACERS

Inside the front of the Multiserver unit, there are
six spacers for positioning the modules (see 

Figure 5-9

). To remove a spacer, simply slide the

spacer up and out of the unit. Set the spacers aside
for reassembly. The bottom-most spacer (the
number 1 spacer in 

Figure 5-9

) should remain in

the unit.

5.5.5  D

ISASSEMBLY

C

ONSIDERATIONS

Adding a CSU/DSU Module. 

The disassembly

procedures end here. Refer to 

MS1 56K CSU/DSU

Module User’s Manual

for installation guidelines.

Adding an RLB (Remote LAN Bridge) Module

. Remove

the CSU/DSU module (if appropriate). Refer to

MS RLB Module User’s Manual

for installation

guidelines.

Adding a Voice/Fax Module

. Remove the CSU/DSU

module and/or the RLB Module (if appropriate).
Refer to 

MS1 Voice/Fax Card User’s Manual

for

installation guidelines.

Adding a Channel Expansion Module (CEM). 

Remove

Voice/Fax card(s), RLB Module, and/or CSU/DSU
module (if appropriate). See 

Section 5.7.1

for

installation guidelines.

Adding an NMS Module. 

The addition of the NMS

module will require the removal of all the modules,

including the CCM. Follow the CCM Removal
instructions (

Section 5.5.7

). Refer to the 

MS1 NMS

Module User’s Manual

for installation guidelines.

5.5.6  R

EMOVING A

C

HANNEL

E

XPANSION

M

ODULE

(CEM), V

OICE

/F

AX

C

ARD

, 

OR

CSU/DSU M

ODULE

1. Disconnect any external cables connected to the
module.

2. Unscrew the two screws in the back panel.

3. Gently remove the board by lifting it up and
making sure that the stacking connectors
disengage.

4. Remove the spacer associated with the module if
you need to remove the next module.

5.5.7  R

EMOVING THE

CCM

1. Before removing the CCM, remove the
CommPak cartridge and place it in an antistatic
bag. (See 

Section 4.2, CommPak Cartridge

Installation and Removal

.)

2. Disconnect all external cables \connected to the
CCM. Remove any converters, if installed.

3. Disconnect the 12-pin power supply harness from
the CCM (see 

Figure 5-10

).

4. Disconnect the 26-pin LCD ribbon cable from
the CCM.

26-PIN RIBBON

CONNECTOR FROM LCD

12-PIN POWER

CONNECTOR

34-PIN RIBBON CONNECTOR

FROM NMS MODULE

FAN CONNECTOR

Figure 5-10. Disassembling the CCM.

Содержание 5000 MX215C, 5000 MX218C













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды