Black Box 5000 MX215C, 5000 MX218C Скачать руководство пользователя страница 233

Страница: 233 / 268

Appendix D: Messages

231

RESET REQ’D

Info

You have changed the sync protocol and did not
perform a reset. It is necessary to reset the node
before proceeding.

RING DETECTED LINK #

Event

The number dialed (TX or RX, primary or secon-
dary) is ringing. This message is displayed by the
call answering modem.

RX CONNECTION MADE

Event

A successful call was placed over the dial lines

LINK #

from the modem’s RX dial-line connection. This
message is displayed by the call answering modem.

SIGNAL PROCESSOR FAIL

Event

The modem failed the self-test. Contact your
dealer.

SIGNAL PROCESSOR PASS

Event

Self-test complete.

SL TIME OUT

Info

Sync loss has occurred continuously for 40
seconds.

SYNC ACQUIRE

Event

Synchronization has been achieved with the remote
Multiserver unit or feeder mux attached on link

SYNC CHANNEL

Diagnostic

Synchronous port

on node

has been

LOOPBACK

n/c

placed into loopback mode.

SYNC CHANNEL

n/c

Alarm

Synchronous port

on node

has lost its

STOPPED

output clock, or input end of frame is missing.

SYNC LOSS LINK

Alarm

Synchronization has been lost with the remote
Multiserver unit or feeder mux on link

TEST CLEARED LINK #

Diagnostic

A modem test has been terminated.

THE CHANNEL MUST BE

Info

Appears when a channel type or protocol change

DISCONNECTED

is requested and the port is connected.

TIMEOUT

Info

The request is not accepted by the modem.

TRANSMIT/RECEIVE

Event

A call is being transmitted or received.

RING DETECT LINK

TRANSMITTER BUSY

Event

The local transmitter detected a busy signal.

LINK

TRANSMITTER

Event

The ADB software is dialing the transmitter

DIALING LINK

number for link

Screen Display Messages

Message

Message Type

Explanation

Содержание 5000 MX215C, 5000 MX218C












































































































































































































































































Результаты поиска

Содержание 5000 MX215C, 5000 MX218C

Отзывы:

Бренды по названию

Популярные бренды

Black Box 5000 MX215C, 5000 MX218C, Руководство пользователя

Результаты поиска

Содержание 5000 MX215C, 5000 MX218C

Отзывы:

Бренды по названию

Популярные бренды