manualshive.com logo in svg

Black Box 5000 MX215C, 5000 MX218C, Руководство пользователя

Поделиться
Скачать
Black Box 5000 MX215C, 5000 MX218C Скачать руководство пользователя страница 135

CHAPTER 11: Administration

133

11.2  The Command Mode

The Command Mode is a single menu which
supports configuration and testing of the local port
and access to the Command Facility Main Menu.
The local port is defined as the one to which the
terminal you are using is connected.

E

NTERING THE

C

OMMAND

M

ODE

The Command Mode is accessible from any local
async port. Local ports are those on the Multiserver
or any of its attached feeder muxes. At any time,
two ports plus the command port (on the optional
NMS module) may access the Command Mode. 

The terminal you use must initially meet the
specifications outlined in 

Section 6.2, Connecting

an ASCII Terminal

, and 

Table 6-1

. The parameters

can be reconfigured.

Access the Command Modes by 

^X

followed by

<break>

. (Async channels can be configured to

also accept 

^X^Y

. This is done through option 8 of

the Channel Features menu. See 

Section 9.3,

Asynchronous Channels

, and 

Table 9-11

for further

information.)  

The Command Mode menu will appear:

The options of this menu are detailed in 

Table 11-2

on the following page.

E

XITING THE

C

OMMAND

M

ODE

There are two ways to exit the Command Mode:

• Select option 4, Exit, from the Command Mode

Menu.

• Press 

<break>

.

COMMAND MODE: CHANNEL xxx

1. ASYNC LOCAL LOOPBACK

2. LOCAL CHANNEL CONFIGURATION

3. COMMAND FACILITY MAIN MENU

4. EXIT

CR - ACCEPT ENTRY

ENTRY: 

Содержание 5000 MX215C, 5000 MX218C













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды