manualshive.com logo in svg

Black Box 5000 MX215C, 5000 MX218C, Руководство пользователя

Поделиться
Скачать
Black Box 5000 MX215C, 5000 MX218C Скачать руководство пользователя страница 128

Multiserver 5000

126

or

Initiated by Multiserver (or remote end):

1.

Calling

device disconnects. 

2. Multiserver drops CTS, DSR, and CD. 

3. Port is marked out-of-service until device

acknowledges disconnect by dropping
then raising DTR.

A

UTO

(A

NSWER

) P

ROTOCOL

Call Request

(

Calling

port attached to a dialup

modem)

Idle State:

Ring (Busy at the Multiserver) is

low

.  Other control signal levels are

ignored.  Multiserver holds CTS,
DSR, and CD 

off

.

1. Device sends ring/no-ring cycle (RI 1

second

on

, 2 seconds 

low

).

2. Multiserver raises DSR (DTR at modem)

and CTS (RTS at modem) when RI goes

low

.

3. Modem raises DSR (DTR at Multiserver)

and CTS (RTS at Multiserver) within 60
seconds.

4. If ABR is enabled, 

<cr> 

should now be

typed (see 

Section 9.3, Asychronous

Channels

).

Call Completion

(

Receiving

port)

1. Multiserver sends ring cycles (RI 2

seconds

on

, 4 seconds 

off

).

2. Device must raise DTR within 2 ring

cycles or it will be made inoperable until
it does.

3. Multiserver has 2 seconds to raise DSR

and CTS.

Disconnect Sequence

Initiated by device:

1. Device drops DTR. 

2. Multiserver drops DSR and CTS.

Initiated by Multiserver (or remote end):

1. Multiserver drops DSR and CTS. 

2. If Call Inhibit is

on

, the channel will be

marked out-of-service until device drops
DTR.

10.10  Port Contention/Queueing

Port contention allows multiple users access to a
limited number of resources.

If no resource is idle, the user will be placed in
queue for the busy ports in the primary or
secondary class.

Once in the queue, the user may receive the
current queue message (

Waiting Q = 

your place

in the queue) by typing in any printable ASCII
character or a 

<cr>

.  The user may also exit the

queue (and return to the resource prompt) by
pressing the 

<break>

key.

Содержание 5000 MX215C, 5000 MX218C













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды