manualshive.com logo in svg

Black Box 5000 MX215C, 5000 MX218C, Руководство пользователя

Поделиться
Скачать
Black Box 5000 MX215C, 5000 MX218C Скачать руководство пользователя страница 242

Multiserver 5000

240

Table E-2.  CCM Indicator LEDs

INDICATOR STATUS

EQUIPMENT STATUS

AT

BO

A6

A5

A4

A3

A2

A1

1

0

X

X

X

X

X

X

1

Normal equipment status

0

0

1

0

0

0

0

0

ROM Test Failure (CommPak cartridge
failure)

0

0

0

0

0

0

0

1

CMOS Failure

2

0

0

0

0

0

0

1

0

Battery low

3

0

1

1

0

0

0

0

0

RAM Failure in Commpak cartridge

1

0

1

0

1

0

1

0

Parity error

1

1

1

1

1

1

1

1

CommPak cartridge not installed
properly or defective Multiserver unit

0

1

0

0

0

0

0

0

RAM Test Failure (CCM)

KEY

0 = LED off
1 = LED on
X = LED will change with the status of the Multiserver.

1

If A1 is configured as a link, it blinks on power-up with no established link.  (The default setting is for A1 to be
configured as a link.)

2

System can still operate with CMOS failure.  All configuration data has been lost in the affected CMOS section,
and default values have been supplied.

3

System can still operate with a low battery.  Configuration data may be lost if the Multiserver loses power.

Содержание 5000 MX215C, 5000 MX218C













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды