manualshive.com logo in svg

Black Box 5000 MX215C, 5000 MX218C, Руководство пользователя

Поделиться
Скачать
Black Box 5000 MX215C, 5000 MX218C Скачать руководство пользователя страница 231

Appendix D:  Messages

229

NO ASYNC CHANNELS

Info

A port or ports in the range selected is not

WITHIN RANGE

configured for async.

NODE-CHANNEL NOT AVAILABLE

Info

A link port number was entered when

ENTER CARRIAGE RETURN

a sync, async, or voice/fax channel number

TO CONTINUE

was required.

NODE ID ALREADY IN USE

Info

You are trying to configure a node ID that has
already been assigned in the network.

NODE NUMBER ALREADY

Info

You are trying to configure a node number

IN USE

that has already been assigned in the network.

ni

NO DIAL TONE LINK # 

ci

Event

The automatic dial-backup function was unable to
detect a dial tone when it went off hook to place a
call over the RX or TX dial lines.

ni

NO RECEIVER

Event

The ADB feature could not detect a dial tone at

DIAL TONE LINK 

ci

the receiver.  Check the phone connection.

NO REMOTE CONNECT

Info

The user is attempting a remote echo/fox test

ACTIVE

from Command Mode with no connection made.

NO SYNC CHANNELS

Info

A port or ports in the range selected are not

WITHIN RANGE

configured for sync.

ni

NO TRANSMITTER

Event

The ADB feature could not detect a dial tone

DIAL TONE LINK 

ci

at the transmitter.  Check the phone line.

NOT ALLOWED

Event

An invalid mode of operation has been entered; it
will not be supported.

NOT SUPPORTED

Info

The requested voice/fax configuration parameter
selected is not supported by your voice/fax module.

ni

NUMBER NOT

Event

The ADB number has not been configured for

CONFIGURED LINK 

ci

link 

ci

; the ADB operation cannot continue.

NUMERIC REQUIRED

Info

The entry received was not a number.

OPERATIONAL PROCESSOR FAIL

Event

The modem failed the self-test.  Contact your

FAIL

dealer.

OPERATIONAL PROCESSOR PASS

Event

Self-test complete.

OUT OF RANGE

Info

The range of numbers entered is not available in the
unit.

Screen Display Messages

Message

Message Type

Explanation

Содержание 5000 MX215C, 5000 MX218C













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды