Black Box 5000 MX215C, 5000 MX218C Скачать руководство пользователя страница 234

Страница: 234 / 268

Multiserver 5000

232

TRANSMITTER RING

Event

A call is coming in on the transmitter side.

DETECT LINK

TX CONNECTION MADE

Event

A successful call was placed over the dial-lines

LINK #

from the modem’s TX dial line connection. This
message is displayed by the call-originating modem.

Dialog

• Node, class, module location, or port is unknown

in the network.

• Password for the class may be incorrect.
• If matrix switching is disabled, this message will

display when matrix switching is attempted.

Dialog

Requested resource exists, but is not in service (not
operational). Call inhibit may be off or DTR is off.

VOICE CHANNEL

Event

Voice/fax port

on node

has been put in a

[

n/c

] [condition]

busyout state. [Conditions] may be the

BUSY OUT

following:

System

Where the link has experienced a sync
loss, a force-disable command, or a
force-disconnect command.

Forced

Where the network operator has put the
channel in a busyout condition via a
forced-busy command.

VOICE CHANNEL [

n/c

]

Event

Termination of a busyout condition has

BUSYOUT CLEARED

occurred on voice/fax channel

VOICE CHANNEL [

n/c

]

Event

The current dBm level for voice/fax port

INPUT LEVEL:

dBm

on node

(-25 to +1) dBm.

- [

display

] -

Note:

[

Display

] is a dynamic display

which appears on the screen.

VOICE CHANNEL [

n/c

]

Diagnostic

Voice/fax port

on node

has started the

LOCAL LOOP TEST

diagnostic local loop test.

VOICE CHANNEL

Event

The voice/fax port has been reset and

[

n/c

] RESET

re-initialized to the current configuration.

VOICE CHANNEL [

n/c

]

Diagnostic

Voice/fax port

on node

has completed

SELF TEST FAIL

the internal diagnostic tests unsuccessfully.

VOICE CHANNEL [

n/c

]

Diagnostic

Voice/fax port

on node

has completed

SELF TEST PASS

the self-tests successfully.

Screen Display Messages

Message

Message Type

Explanation

Содержание 5000 MX215C, 5000 MX218C












































































































































































































































































Результаты поиска

Содержание 5000 MX215C, 5000 MX218C

Отзывы:

Бренды по названию

Популярные бренды

Black Box 5000 MX215C, 5000 MX218C, Руководство пользователя

Результаты поиска

Содержание 5000 MX215C, 5000 MX218C

Отзывы:

Бренды по названию

Популярные бренды