manualshive.com logo in svg

Black Box 5000 MX215C, 5000 MX218C, Руководство пользователя

Поделиться
Скачать
Black Box 5000 MX215C, 5000 MX218C Скачать руководство пользователя страница 60

Multiserver 5000

58

6.6  Quick Setup

C

AN

Y

OU

D

O A

Q

UICK

S

ETUP

?

A quick installation can be done to get a point-to-
point Multiserver network up and running in a
short amount of time. You will be force-connecting
all the channels within the network (A2 to A2, A3 to
A3, etc.). Only channels of like type will be
connected. Voice channels cannot be force-
connected to data channels, so all hardware
components must match. 

Caution

Do not use these procedures if you
have the RLB Module installed.

If your network is not a point-to-point network or if
the hardware configuration of the Multiservers
differ, you cannot do a quick set up. Proceed to

Chapter 8.0, Installing and Configuring the Link

.

NOTE:  These procedures assume that the ports on

the Multiserver have not been configured
and have their default settings.

P

RELIMINARY

S

TEPS

• All modules should be installed in the base unit

(see 

Chapter 5.0, Module Installation

). 

• Install your Multiservers at their locations (see

Chapter 4.0, Base Unit Installation

). 

• Hook up a terminal to any asynchronous port.

Make sure the terminal characteristics are
compatible with the Multiserver (see 

Section 6.2, Connecting an ASCII Terminal

).

• You will need to assign the local node a number

and name to differentiate it from the remote
node. (See 

Section 6.6, Naming the Local

Node

.)

T

HE

I

NTERCONNECT

L

INK

• Hook up the interconnect link using either

CSU/DSU modules, external CSU/DSUs, or
external modems.

• Plug in your Multiserver and check the A1

indicator. The indicator should be off. If the A1
indicator is on or flashing, there is a problem
with the link; you cannot do a quick installation.
See 

Chapter 8.0, Installing and Configuring the

Link

.

Figure 7-1. Point-to-point network, all channels force-connected.

A3

A4

B12

A3

A4

B12

Содержание 5000 MX215C, 5000 MX218C













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды