Black Box 5000 MX215C, 5000 MX218C Скачать руководство пользователя страница 229

Страница: 229 / 268

Appendix D: Messages

227

ISU LOCAL LOOPBACK

Diagnostic

The ISU on link

has been placed in local

ACTIVE LINK #

loopback.

ISU LOCAL

Diagnostic

This test puts the local ISU on link

LOOPBACK WITH TP

loopback, then verifies the operation of the

ACTIVE LINK #

ISU by sending and receiving the test pattern.

ISU TEST PATTERN

Diagnostic

The test-pattern generator on the ISU on link

ACTIVE LINK #

has been activated.

ISU TEST

Diagnostic

The test for the ISU on link ci has been

TERMINATED LINK #

terminated.

LAN MODULE

Info

The LAN module in

is not available for use.

LOCATION [

] DOWN

LAN MODULE

Info

The LAN module in

is operating and

LOCATION [

] UP

available.

LEASED LINE CONNECTION

Event

ADB has completed the leased line connection

MADE LINK

for link

LEASE LINE OUT OF

Event

The modem is unable to communicate with the

SERVICE LINK #

remote modem over the leased lines.

LEASE LINE

Event

The modem is operating on the leased lines

RETRY LINK

while the dial lines are still established. ADB mode
is enabled.

LINE ALARM

Alarm

Link

at node

has a line alarm, indicating a high

line error rate.

LINK DOWN

Alarm

The local Multiserver unit has timed out (40
seconds) waiting for sync to be acquired on link

Check the cabling, modem, remote Multiserver unit,
or feeder mux for errors.

LOCAL ANALOG LOOP

Diagnostic

The local analog transmit signal is being

LINK #

looped back into the local analog receiver.

LOCAL Bl-ANALOG

Diagnostic

Both the local analog and VF loopbacks are

LOOP LINK #

being run.

LOCAL Bl-DIGITAL

Diagnostic

This test includes both DTE and digital

LOOP LINK #

loopback tests.

LOCAL CHANNEL

Info

The Local Channel Configuration Menu cannot

CONFIGURATION DISABLED

be accessed by the async port requesting it.

Screen Display Messages

Message

Message Type

Explanation

Содержание 5000 MX215C, 5000 MX218C












































































































































































































































































Результаты поиска

Содержание 5000 MX215C, 5000 MX218C

Отзывы:

Бренды по названию

Популярные бренды

Black Box 5000 MX215C, 5000 MX218C, Руководство пользователя

Результаты поиска

Содержание 5000 MX215C, 5000 MX218C

Отзывы:

Бренды по названию

Популярные бренды