BendPak PL-6000DC Скачать руководство пользователя

Страница: 9 / 88

PL-6000DC Two Post Parking Lift

P/N 5900273 — Rev. A1 — May 2022

Frequently Asked Questions

Question

: What kinds of Vehicles can I park on my PL-6000DC Lift?

Answer

: Cars, light trucks, and SUVs; up to 6,000 lbs. (2,722 kg) per Platform. The vehicle’s Wheels

must fit on the 82.5 in / 2,100 mm x 146 in. / 3,700 mm Lift Platform.

: Does the Lift have to be anchored in place?

: Yes. The Lift Posts

must

be anchored.

: Can I install my Lift outside?

: The Lift is designed for indoor installation only.

Outdoor installation is prohibited.

: Can I use my Lift to store boxes of stuff instead of a Vehicle?

: No. This is

not

the intended use of the Lift; it is

not

designed to be used this way.

: How high does my garage ceiling have to be to support my Vehicles?

It depends on the height of the Vehicles you are putting on the Platforms.

If you are

parking low-slung Vehicles, then your ceiling does not have to be as high as it would need to be if you

are parking taller Vehicles. Refer to Height Requirements and

Will My Car Fit?

for additional

information.

: Does the Control Console have to be connected to the Powerside Post?

: Yes. That location gives the operator a clear view of the Platforms as they are raised and lowered.

: Does it matter if I drive my Vehicles in front first or back them in?

: No. Your Lift works great either way. Make sure to park all Vehicles in the middle of the Platform,

width-wise, no matter which way you drive them in. All four wheels must be completely on the Lift

Platform. Do not park the Vehicle’s Wheels on the Ramp, the Back Stop or the Side Beams.

: How long can I leave a Vehicle on a raised Platform?

: As long as you want, as long as it rests on a Safety Lock. Once a Safety Lock is engaged, gravity

holds it in position, so a loss of power does not impact the Lift. Your Vehicle is going to stay where you
left it. Remember to

always leave the Platform either on the ground or engaged on its

Safety Locks

Содержание PL-6000DC
























































































Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды

BendPak PL-6000DC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды