BendPak PL-6000DC страница 27 Скачать руководство пользователя | Manualshive

Страница: 27 / 88

background image

PL-6000DC Two Post Parking Lift

27

P/N 5900273 — Rev. A1 — May 2022

Drawing not to scale.

Do

not

stand up the Offside Post yet.

Attach the Side Beams, Back Plate and Connection Rods

This section addresses attaching the Side Beams, Connection Rods, and Back Plate. These
components are heavy.

⚠

WARNING

You

must

wear OSHA-approved (publication 3151) appropriate protective

equipment at all times during installation: leather gloves, steel-toed work boots, eye
protection, back belts, and hearing protection are

mandatory

.

⚠

WARNING

The components are heavy and their weight is not evenly distributed. Use proper

tools, Forklift or Shop Crane, and assistants to move the posts into position.

To attach the Side Beams, Back Plate, and Connection Rods:

1.

Attach the Left Side Beam onto the Powerside Post Lift Carriage. Use four sets of M20 x 110 Hex
Head Bolts, Ø20 mm Flat Washer, Ø20 mm Lock Washer and M20 Hex Nut. Verify the Hex Bolt

heads and Flat Washers are on the inside of the Lift and the Nuts, Lock Washers on the outside of

the Beam facing out from the Lift. Refer to the figure on the next page.

2.

Attach the Right Side Beam onto the Offside Post Lift Carriage. Use the same Fasteners as
referenced in step 1 above. Verify the Hex Bolt heads and Flat Washers are on the inside of the Lift
and the Nuts, Lock Washers on the outside of the Beam facing out from the Lift.

Do not install

the Four M20 x 55 Hex Head bolts at this time

. Refer to the figure on the next page.

«
...
25
26
27
28
29
...
»

Содержание PL-6000DC

























































































Отзывы:

Нет отзывов

Похожие инструкции для PL-6000DC

Бренд: Handicare Страницы: 32

Бренд: SanRex Страницы: 98

MoveAround MA50

Бренд: Safelift Страницы: 20

Бренд: ICP DAS USA Страницы: 6

Бренд: Balluff Страницы: 124

Caddy Tig 1500i TA34

Бренд: ESAB Страницы: 50

Бренд: Measurement Computing Страницы: 50

Бренд: Victor Страницы: 168

Бренд: Powerdist Страницы: 7

Бренд: Marshall Amplification Страницы: 30

Бренд: M-system Страницы: 2

DYNAMIC HEAT CONTROL PLUS Series

Бренд: Napoleon Страницы: 72

Бренд: Würth Страницы: 292

niagara4 MultiSITE Edge 10

Бренд: LG Страницы: 73

Бренд: Sanyo Страницы: 22

Бренд: ProMinent Страницы: 2

Бренд: PROMETHEUS Страницы: 39

Бренд: Inder Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды