manualshive.com logo in svg

BendPak PL-6000DC, Инструкция по установке и эксплуатации

BendPak PL-6000DC - hydraulic car lift designed for easy maintenance and operation. Ensure proper installation and safety by downloading the free Installation And Operation Manual from our website. Не забудьте загрузить его с manualshive.com для безопасного использования.

Поделиться
Скачать
background image

 

Manual.

 PL-6000DC Parking Lift, 

Installation and Operation Manual

, Manual P/N 5900273, Manual Revision A1, 

Released May 2022. 

Copyright.

 Copyright © 2022 by BendPak Inc. All rights reserved. You may make copies of this document if you 

agree that: you will give full attribution to BendPak Inc., you will not make changes to the content, you do not gain 

any rights to this content, and you will not use the copies for commercial purposes. 

Trademarks.

 BendPak and the BendPak logo are registered trademarks of BendPak Inc. All other company, 

product, and service names are used for identification only. All trademarks and registered trademarks mentioned 
in this Manual are the property of their respective owners. 

Limitations.

 Every effort has been made to ensure complete and accurate instructions are included in this 

Manual. However, product updates, revisions, and/or changes may have occurred since this Manual was 

published. BendPak reserves the right to change any information in this Manual without incurring any obligation for 

equipment previously or subsequently sold. BendPak is not responsible for typographical errors in this Manual. 
You can always find the latest version of the 

manual for your product on the BendPak website

. 

Warranty.

 The BendPak warranty is more than a commitment to you: it is also a commitment to the value of 

your new product. Contact your nearest BendPak dealer or visit 

www.bendpak.com/support/warranty

 for 

full warranty details. 

Go to 

bendpak.com/support/register-your-product/ 

and fill out the online form to 

register your product (be sure to click Submit). 

Safety.

 Your Lift was designed and manufactured with safety in mind. However, your safety also depends on 

proper training and thoughtful operation. Do not install, operate, maintain, or repair the unit without reading and 

understanding this Manual and the labels on the unit; 

do not use your Lift unless you can do so safely!

 

Owner Responsibility.

 In order to maintain your product properly and to ensure everyone’s safety, it is the 

responsibility of the product owner to read and follow these instructions: 

•  Follow all installation, operation, and maintenance instructions. 
•  Make sure product installation conforms to all applicable local, state, and federal codes, rules, and regulations, 

such as state and federal OSHA regulations and electrical codes. 

•  Read and follow all safety instructions. Keep them readily available for operators. 

•  Make sure all operators are properly trained, know how to safely operate the unit, and are properly supervised. 
•  Do not operate the product until you are certain that all parts are in place and operating correctly. 

•  Carefully inspect the product on a regular basis and perform all maintenance as required. 

•  Service and maintain the unit only with approved replacement parts. 

•  Keep instructions permanently with the product and make sure all labels are clean and visible. 
•

 

BendPak

 makes no promises, guarantees or assurances that our products meet any state, county, federal or 

international mandated permit, license, code, standard, certification, or any other mandate other than what is 

listed or shown on BendPak website(s), or any BendPak or Ranger online or published catalog. Not all 

BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV-(current edition) or ANSI/UL 201. 

Consult 

www.autolift.org 

for a complete list of lift models that meet ANSI/ALI ALCTV-(current edition) or 

ANSI/UL 201, or contact BendPak via 

[email protected]

. 

Buyer assumes full responsibility 

for any state, county, federal or international mandated permit, license, code, standard, 

certification, or any other mandate required related to the installation and/or operation of 

any BendPak or Autostacker product.

 BENDPAK will not be responsible for any charges, fines, liens, 

or other levies imposed on the Buyer related to any special or regional structural, seismic or any other building 

code and/or codes such as the Uniform Building Code (UBC), International Building Code (IBC), or any other 

state, county, federal or international mandated permit, license, code, standard, certification, or other 

mandate, law, rule, regulation or directive by any other agency, government, administrations, or corporations 
whether state, county, federal, or international mandated. 

• 

Only use the Lift if it can be used safely!

  

 

Содержание PL-6000DC

























































































Отзывы:

Нет отзывов

Похожие инструкции для PL-6000DC

Jäger ADwin-Gold Hardware Manual preview
ADwin-Gold
Бренд: Jäger Страницы: 50
Notifier AUTOPULSE IQ-318 Manual preview
AUTOPULSE IQ-318
Бренд: Notifier Страницы: 62
FAAC B614 Translation Of The Original Instructions preview
B614
Бренд: FAAC Страницы: 63
BUCKINGHAM MFG OX BLOCK Instructions And Warnings preview
OX BLOCK
Бренд: BUCKINGHAM MFG Страницы: 7
American Panel IC+ Manual preview
IC+
Бренд: American Panel Страницы: 18
Fenix AT-05 Instructions Manual preview
AT-05
Бренд: Fenix Страницы: 24
Aqua-Hot 375D Installation Manual preview
375D
Бренд: Aqua-Hot Страницы: 49
Lincoln Electric INVERTEC CC400-T Operator'S Manual preview
INVERTEC CC400-T
Бренд: Lincoln Electric Страницы: 48
M-system R7D-DC16B Instruction Manual preview
R7D-DC16B
Бренд: M-system Страницы: 10
M-system Devicenet R7F4DD-DC16B-H Instruction Manual preview
Devicenet R7F4DD-DC16B-H
Бренд: M-system Страницы: 7
Launch TLT260AT User Manual preview
TLT260AT
Бренд: Launch Страницы: 32
LaserStar iWeld 900 Series Operation & Maintenance Manual preview
iWeld 900 Series
Бренд: LaserStar Страницы: 172
Lincoln Electric OPTIMARC CV355P Operator'S Manual preview
OPTIMARC CV355P
Бренд: Lincoln Electric Страницы: 17
National Instruments FOUNDATION Getting Started preview
FOUNDATION
Бренд: National Instruments Страницы: 49
National Instruments 9232 Operating Instructions And Specifications preview
9232
Бренд: National Instruments Страницы: 43
National Instruments BNC-2090A User Manual preview
BNC-2090A
Бренд: National Instruments Страницы: 50
National Instruments DAQ Installation Manual preview
DAQ
Бренд: National Instruments Страницы: 52
Faraone ELEVAH 61 Translation Of The Original Instructions preview
ELEVAH 61
Бренд: Faraone Страницы: 62

Бренды по названию

Популярные бренды

Загрузить еще бренды