BendPak PL-6000DC Скачать руководство пользователя | Manualshive

Страница: 51 / 88

background image

PL-6000DC Two Post Parking Lift

51

P/N 5900273 — Rev. A1 — May 2022

Connect To Power

Connect the Power Unit to an appropriate Power Source through the Power Disconnect Switch.
Power for this Lift is 220 VAC, 60 Hz. single phase and should be protected by a 25 Amp fuse or
circuit breaker.
Refer to the

Wiring Diagram

and

Control Console Wiring Diagram

for further information.

⚠

DANGER

All wiring

must

be performed by a licensed, certified Electrician in accordance with

all applicable national and local electrical codes. Do not perform any maintenance

or installation on the Lift without first making sure that main electrical power has
been disconnected from the Lift and cannot be re-energized until all procedures are

complete.

⚠

WARNING

Keep Wiring and Hydraulic Hoses away from sharp edges or pinch points to avoid

damage.

Important Electrical Information:

•

Improper electrical installation can damage the Power Unit Motor. This damage is

not

covered

under warranty.

•

Use a separate Circuit Breaker for each Lift Installed.

•

Protect each circuit with a 25 Amp time-delay fuse or circuit breaker.

To connect the Lift to Power

:

Verify the Power is disconnected and locked out to prevent re-energizing while you work on the

Lift.

Connect the Main Power Supply wiring to the Power Disconnect Switch just installed using an

appropriate gauge wire for the voltage, current and length of run.

Route the Power wiring from the Power Disconnect up to the Junction Box on the Power Unit.

Refer to the

Wiring Diagram

and

Control Console Wiring Diagram

to connect the power

to the Contactor and Thermal Disconnect, the Solenoid, and Control Console in the Junction Box.

Wire the Power Unit Junction Box

The Junction Box houses the wiring and connections for Power, Thermal Overload, Limit Switch,
Solenoid and the Lift Controls.The Controls on the Console allow the operator to raise and lower

Vehicles. Refer to the figure above and the

Wiring Diagram

and

Control Console Wiring

for wiring information.

⚠

DANGER

All wiring

must

be performed by a licensed, certified Electrician in accordance with

all applicable national and local electrical codes.

The Junction Box wiring includes:

•

Power

. Wiring connections for power supplied to the Hydraulic Power Unit from the Power

Disconnect Switch.

•

Control Console

. This wiring includes the Up, Down and Emergency Stop Lift functions.

•

Limit Switch

. This Switch stops the upward motion of the Lift Platform.

•

Solenoid

. The Solenoid opens the Hydraulic Valve allowing the Lift Platform to Lower.

«
...
49
50
51
52
53
...
»

Содержание PL-6000DC

























































































Отзывы:

Нет отзывов

Похожие инструкции для PL-6000DC

Бренд: Happ Страницы: 49

EnviroLift EW0820S090

Бренд: Challenger Lifts Страницы: 23

KPH 370.70 LIKT

Бренд: rav Страницы: 82

Бренд: Aqua Creek Страницы: 3

PYTHON-PLUS K2447-1

Бренд: Lincoln Electric Страницы: 39

ArcCharger N550C DOMESTIC

Бренд: Nelson Страницы: 65

Бренд: ESAB Страницы: 44

AlumaPower 450 MPa

Бренд: Miller Страницы: 48

Бренд: Goodman Страницы: 28

ID ISC.ANT.U500/270

Бренд: Feig Electronic Страницы: 54

Бренд: GeoVision Страницы: 4

ERCOLE QK-E2500

Бренд: Quilo Страницы: 10

Бренд: ims PRO Страницы: 78

Бренд: morse Страницы: 8

Бренд: Fitel Страницы: 4

Бренд: Shindaiwa Страницы: 38

Бренд: iBell Tools Страницы: 19

Бренд: Sunex Tools Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды