BendPak PL-6000DC Скачать руководство пользователя

Страница: 45 / 88

PL-6000DC Two Post Parking Lift

P/N 5900273 — Rev. A1 — May 2022

Connecting the Safety Lock Release Cable

A Wire Rope connects the Safety Lock Release Handle to the Safety Lock Release Mechanism. The

Wire Rope is factory installed and routed from the Release Handle through the Control Arm, around a
Sheave and then up and out of the Control Arm to be attached to the Rocker Arm on the Release

Mechanism. Refer to the figures below.

To Attach the Safety Lock Release Cable

Route the Release Cable from where it exits the Control Arm up to the Rocker Arm on the Release

Mechanism. Refer to the figures below.

Connect the end of the Safety Release Cable from the Control Arm to the Rocker Arm Assembly

on the Safety Lock Release Angle using the Cable Clamp.

Adjust the Safety Release Cable tension using the Wire Rope Clamp until a smooth motion is

achieved on the Safety Release Mechanism, when pulling on the Manual Safety Lock Release

Handle.

Содержание PL-6000DC
























































































Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды

BendPak PL-6000DC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды