BendPak PL-6000DC Скачать руководство пользователя | Manualshive

Страница: 56 / 88

background image

PL-6000DC Two Post Parking Lift

56

P/N 5900273 — Rev. A1 — May 2022

Operation

This section describes how to operate your Lift.

⚠

DANGER

When you even hear the words “automotive lift,” your brain should automatically
remember that lifting a Vehicle is a serious endeavor with life-threatening risks.

Focus on what you are doing. Automotive Lifts are dangerous tools when used by
inexperienced or impaired operators.

Do not assume you are going to be

safe this time because nothing happened last time

.

Safety Considerations

Do the following before you raise or lower a Vehicle:
•

Check the Lift

. Walk all the way around the Lift, checking for any missing, heavily worn, or

damaged parts. Always verify all Hydraulic connections including Hydraulic Fittings, Hoses, and

Auxiliary Ports are secure. Do not operate the Lift if you find any issues; instead, take it out of

service, then contact your dealer, email

[email protected]

, or call

(800) 253-2363

,

extension 196.

•

Check the area

. Keep the area around the Lift clean and free of obstructions; anything that

could cause a problem for the Lift or interfere with driving a Vehicle onto or off of the Lift. Do not
forget to check

above

the Lift. If you find an obstruction, move it out of the way. If you find any

other issues, resolve them before using the Lift. Do not allow anyone or anything within 10-feet (3

meters) of the Lift while it is in motion.

•

Check the operators

. Make sure that everyone who is going to operate the Lift has been

trained in its use, has read the Labels on the unit, and has read the Manual. Only the operator at

the Console should be within 30 feet of the Lift when it is in motion.
Do not allow children to operate the Lift. Do not allow anyone under the influence of drugs or

alcohol to operate the Lift. Do not allow any unauthorized personnel to operate the Lift.
When the Lift is moving, the Operator must be paying full attention to the Lift and the area around

it. The Operator must not be looking down at a smart phone, talking to a co-worker, or be
distracted in any other way.

•

Check for safety

. Make sure everyone who is going to be walking near the Lift is aware of its

presence and takes appropriate safety measures. Only put Vehicles on the Platforms.

When

raising a Vehicle, do not leave it until it is on a Safety Lock

. When lowering the Lift, do

not leave it until it is on the ground.

•

Check the Vehicle

. Never exceed the Lift’s weight rating. Do not allow people inside a Vehicle

you are going to raise. Take any articles you may need out of the Vehicle. Verify the Vehicle is not

overbalanced on either end or either side.

«
...
54
55
56
57
58
...
»

Содержание PL-6000DC

























































































Отзывы:

Нет отзывов

Похожие инструкции для PL-6000DC

ECL Comfort 110

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 16

Бренд: Racal Instruments Страницы: 64

Бренд: Parkside Страницы: 201

Бренд: ABICOR Страницы: 16

TLX-7000-FLRAILKIT

Бренд: IDEAL Страницы: 10

Бренд: Orion Welders Страницы: 51

Бренд: Hach Страницы: 504

Бренд: Zepro Страницы: 64

Бренд: Tews Technologies Страницы: 19

Бренд: GST Страницы: 3

Бренд: zika Страницы: 13

Бренд: Chimera Страницы: 14

HS 300 LARGE | FH

Бренд: R. Beck Maschinenbau Страницы: 42

Бренд: Champion Autolift Страницы: 14

Бренд: WARPP Страницы: 11

CADB/T-HE PRO-REG Series

Бренд: S&P Страницы: 72

PATRIOT PORTABLE LIFT

Бренд: Aqua Creek Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды