BendPak PL-6000DC Скачать руководство пользователя

Страница: 42 / 88

PL-6000DC Two Post Parking Lift

P/N 5900273 — Rev. A1 — May 2022

Install the Safety Lock Release Angle

The Safety Lock Release Handle is mounted to the Control Arm. The Safety Locks are released by the

Safety Lock Release Handle linked by Wire Rope to a Safety Release Angle mechanism on the
Powerside Post.

To Install the Safety Lock Release Angle

Install the Safety Release Angle (a) on the front side of the Powerside Post. The release angle functions

a part of the Safety Lock Release mechanism. It is supported by a Rocker Arm (b) and two smaller

Straight Arms (c and d). Secure using M6 x 25 Hex Head Bolt and M6 Locknuts. Attach the Rocker
Arm using M6 x 35 Hex Head Bolts and Locknuts. Verify the mechanism moves freely after securing

the fasteners. Review the figures and details below.

Drawing not to scale.

Содержание PL-6000DC
























































































Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды

BendPak PL-6000DC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды