BendPak PL-6000DC Скачать руководство пользователя

Страница: 25 / 88

PL-6000DC Two Post Parking Lift

P/N 5900273 — Rev. A1 — May 2022

Anchoring the Powerside Post

The Powerside Post

must

be anchored to prevent movement.

⚠

WARNING

You

must

wear OSHA-approved (publication 3151) appropriate protective

equipment at all times during installation: leather gloves, steel-toed work boots, eye
protection, back belts, and hearing protection are

mandatory

⚠

WARNING

The Lift Posts are heavy and the weight is not evenly distributed. Use proper tools,

Forklift or Shop Crane, and assistants to move the posts into position.

Stand-up the

Powerside Post

and move it to the location marked by the chalk lines created

earlier.

Using the

Powerside Post Base

as a pattern, use a Hammer Drill to create Ø12 mm holes 130

mm deep in the concrete. See figure below.
Drilling accurate holes for Expansion Anchors in Concrete is both critical and challenging. If the

Holes for the Anchors are too big, the Anchor will not expand correctly and ultimately will not

embed in the hole with enough force to make a good anchor. If the Holes are too small, the
Anchor will be damaged as it is driven in and will not expand to embed correctly. If the hole is

drilled at an angle, the bolt or Nut will not engage the Lifts’ Base Plate with maximum holding

power.

Use the right tools

. A powerful Hammer Drill with new Drill Bits intended for Rotary Hammer

and Masonry use. Ensure the Drill Flutes are at least as long as the hole you are drilling to remove

the material from the hole as you drill.

Check the size of the Drill Bit before you begin

! The drill may be dull and or undersized

from excessive use. An undersized hole is just as bad as an oversized hole. Undersized holes

deform the anchor and do not allow it to embed correctly.

Содержание PL-6000DC
























































































Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды

BendPak PL-6000DC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды