BendPak PL-6000DC Скачать руководство пользователя

Страница: 26 / 88

PL-6000DC Two Post Parking Lift

P/N 5900273 — Rev. A1 — May 2022

Drill a Pilot Hole

. The final hole size is to be Ø12 mm, drill an 8 to 9 mm pilot hole first. Pilot

holes allow straighter, cleaner drilling by removing the material directly in the center of the final drill.

This reduces the amount of force required to keep the final drill straight and perpendicular to the

floor.

Find the Rebar!

Steel Reinforced Concrete is ideal for strong construction, but terrible for drill

bits. Rebar can and will ruin a Masonry Drill Bit, as well as push the drill off center and ruin the

Anchor Hole by making the hole out of round or too big. Hire a contractor to find the rebar in the

location you wish to install your Lift. Many contractors use ground penetrating radar to accurately
locate rebar.

If you hit Rebar

embedded in the Concrete and have not ruined the Anchor Hole by making it

too big or out of round, switch to a rebar cutting drill bit. Slow the drill speed to avoid overheating

the drill bit. Continue drilling until you are past the Rebar.

Use a Depth Gauge

or place tape on the Drill Bit to indicate the final hole depth.

Don’t rush

. Pull the drill out of the hole at regular intervals to clear the material out of the hole as

you drill.

If you see sparks

, stop, you have hit rebar.

Vacuum, brush and blow out

the hole frequently as you drill to clean out the hole.

When the drill has reached its final depth

, clean the hole using a brush, vacuum and/or

compressed air.

Insert the Anchors. Place the Anchor in the opening with a Flat washer and Hex Nut attached. You

may have to tap the Anchors in with a Mallet or Hammer. Do

not

damage the Anchor threads.

Refer to figures below.

not

tighten the Anchor Nuts at this point. Leaving the Nuts finger tight allows for adjustment

and shimming later in the installation.

Содержание PL-6000DC
























































































Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды

BendPak PL-6000DC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды