BendPak PL-6000DC Скачать руководство пользователя

Страница: 32 / 88

PL-6000DC Two Post Parking Lift

P/N 5900273 — Rev. A1 — May 2022

Connecting the Safety Lock Release - Lift Carriages

Safety Locks are triangular shaped spring loaded plates mounted on the Lift Platform that snap into

slots in both Posts preventing downward motion. The Safety Lock Release prevents the Lock from
engaging the slots in the Posts thus allowing the Lift platform to lower.

To install the Safety Lock Release

Mount the Unlocking Pin Seat on the Powerside Side Beam using the existing holes with two M10

x 25 and two M10 Hex Nuts with Flange. Refer to the figure below.

Drawing not to scale.

The Unlocking Rod, Adjustable Joints and Articulated Bearings are installed beneath the Platform

and connect the Triangular Shaped Locks on the Powerside and Offside beams. Refer to the figure

below.

Drawing not to scale.

Содержание PL-6000DC
























































































Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды

BendPak PL-6000DC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды