BendPak PL-6000DC Скачать руководство пользователя | Manualshive

Страница: 5 / 88

background image

PL-6000DC Two Post Parking Lift

5

P/N 5900273 — Rev. A1 — May 2022

You may also contact BendPak for parts replacement information (please have the model and serial

number of your unit available) at

(800) 253-2363

, extension 191.

Shipping Information

Your equipment was carefully checked before shipping. Nevertheless, you should thoroughly inspect
the shipment

before

you sign to acknowledge that you received it.

When you sign a bill of lading, it tells the carrier that the items on the invoice were received in good
condition.

To protect yourself, do not sign until

after

you have inspected the shipment.

If any of

the items listed on the bill of lading are missing or are damaged, do not accept the shipment until the

carrier makes a notation on the bill of lading that lists the missing and/or damaged goods.

If you discover missing or damaged goods

after

you receive the shipment and have signed the bill of

lading, notify the carrier at once and request the carrier to make an inspection. If the carrier will not
make an inspection, prepare a signed statement to the effect that you have notified the carrier (on a

specific date) and that the carrier has failed to comply with your request.
It is difficult to collect for loss or damage after you have given the carrier a signed bill of lading. If this
happens to you, file a claim with the carrier promptly. Support your claim with copies of the bill of

lading, freight bill, invoice, and photographs, if available. Our willingness to assist in helping you

process your claim does not make us responsible for collection of claims or replacement of lost or

damaged materials.

Safety Considerations

Read this Manual carefully before installing or using your new product

.

Do not

install or operate the product until you are familiar with all operating instructions and warnings. Do not

allow anyone else to operate it until they are familiar with all operating instructions and warnings. Keep

this Manual on or near the product for future reference.

⚠

WARNING

California Proposition 65

. This product can expose you to chemicals including

styrene and vinyl chloride which are on the list of over 900 chemicals identified by

the State of California to cause cancer, birth defects or reproductive harm. Always

use this product in accordance with BendPak’s instructions. For more information,

visit

www.p65warnings.ca.gov

Important Safety Information

When using this equipment, basic safety precautions should always be followed, including:
•

Read all instructions. Use only as described in this manual.

•

Only operate your Lift between temperatures of 41°F to 104°F (5°C to 40°C).

•

Make sure all operators read and understand this

Installation and Operation Manual

.

Keep the

manual near the Lift at all times

.

•

The Lift should only be operated by authorized personnel. Keep children and untrained personnel

away from the Lift.

•

Do not make any modifications to the Lift; this voids the warranty and increases the chances of

injury or property damage. Use only factory-approved attachments.

Do not modify any safety

related features in any way

.

«
...
3
4
5
6
7
...
»

Содержание PL-6000DC

























































































Отзывы:

Нет отзывов

Похожие инструкции для PL-6000DC

Бренд: OMA Страницы: 73

Бренд: CAME Страницы: 26

Бренд: CAME Страницы: 34

Бренд: Handicare Страницы: 20

Бренд: Mopedia Страницы: 36

Бренд: Safety Clamps Страницы: 16

Бренд: Xcel-Arc Страницы: 36

DHI-IPMECD-3021 Series

Бренд: Dahua Technology Страницы: 28

COMFORTMATE EQH-20WUS

Бренд: Navien Страницы: 4

HEAVY DUTY HOIST

Бренд: Proslat Страницы: 6

HRU-WALL-RC Series

Бренд: Nalnor Страницы: 32

Бренд: Jackle Страницы: 72

Бренд: Miller Electric Страницы: 32

Бренд: DROPSA Страницы: 11

Бренд: Bosch Страницы: 32

Rexroth CC-CS351

Бренд: Bosch Страницы: 96

Бренд: Bosch Страницы: 10

LTC 8808/00 Series

Бренд: Bosch Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды